Sharif Digital Repository

Carbon nanotubes (CNTs) decorated with Cu2O particles were grown on a Ni catalyst layer deposited on a Cu substrate by thermal chemical vapor deposition from liquid petroleum gas. Ni catalyst nanoparticles with different sizes were produced in an electroplating system at 45 °C using the corrosive effect of H2SO4 which was added to solution. These nanoparticles provide the nucleation sites for CNT growth avoiding the need for a buffer layer. The surface morphology of the Ni catalyst films and CNT growth over this catalyst was studied by scanning electron microscopy (SEM). High temperature surface segregation of the Cu substrate into the Ni catalyst layer and its exposition to O2 at... 

A hot filament chemical vapor deposition (HFCVD) method was used to prepare Fe-Cr thin film on Si substrate. The produced layers were used as catalysts for growing carbon nanotubes (CNTs) from liquid petroleum gas (LPG) at 825 °C by thermal CVD (TCVD) method. To characterize the obtained catalysts or CNTs, X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Raman spectroscopy were used. CNTs were grown on HFCVD derived Fe-Cr catalyst with the LPG as carbon source successfully. It was found that an annealing process on catalysts enhances the surface concentration of Cr atoms and reduces the sizes of catalyst particles. The... 

This research presents an application of transparent lanthanum-modified lead zirconate titanate (PLZT) materials in micro light source tracking device, which is designed to function as a result of irradiation, having neither lead wires nor electric circuits. The focus of the paper is on the analytical and finite element investigation into ultraviolet photo-induced multi-physics responses of PLZT photocantilever and a comparison of the measured bending displacement to check the feasibility of these materials in design of micro light source tracking device. The finite element formulation of the transverse deflection for multi-physics analysis of PLZT ceramics by including the photovoltaic and... 

By fabrication of several bolometric detectors on the YBCO film made of Metal-Organic Deposition (MOD) and the effect of pattering and film parameters on the optical responsivity of transition edge sensors is investigated. The low cost nonfluorine (MOD) method has been applied to fabricate YBCO thin films with different patterning parameters. The measurement results of the optical responsivity versus modulation frequency up to 100 KHz for these devices are reported  

The effect of substrate thickness and its Debye temperature on the bolometric response of the freestanding-membrane type of superconductor transition-edge detectors is investigated. The investigation is based on the calculation of the variation of the specific heat per unit volume and the heat conductivity using the finite-size scaling method for different Debye temperatures and micron size thickness of substrate. We also calculated the heat capacity and time constant for various materials with Debye temperatures in the range of 600-1400 K. The calculated results are compared with previously reported response values obtained theoretically and experimentally for the thermal-based infrared... 

In this study a hot filament chemical vapour deposition (HFCVD) technique was used to prepare Fe-Cr films on Si substrate as catalysts for thermal CVD (TCVD) growing of carbon nanotubes (CNTs) from liquid petroleum gas (LPG) at 800 °C. To characterize the catalysts or CNTs, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy were used. The XPS spectra obtained at different stages of Ar+ sputtering revealed that in the depth of catalyst layers, the relative Fe-Cr concentrations are higher than the top-surface. SEM images of samples after TCVD indicate a significant CNT growing at the backside of catalyst... 

TCVD growth of multiwalled carbon nanotubes (MWCNTs) was reported by catalytic decomposition of liquefied petroleum gas (LPG) at a temperature range of 580800 °C. Laser ablation was employed as a simple and rapid technique to produce Pd nanoparticles which possess effective catalytic activities for CNT synthesis. UVvisible spectroscopy and TEM images confirmed that the Pd nanoparticles are stable for a long time and have rather spherical shape with average size of 7 nm. SEM and TEM observations and Raman spectroscopy demonstrated that the CNTs have a wavy structure, dense morphology and acceptable crystallinity. Since Pd nanoparticles are inactivated or agglomerated at extremes of the... 

The visible band (band A) of photoluminescence spectra of high-purity synthesized diamond is analyzed by the deconvolution technique. A set of eight lines with distinct peak energies are found. The peak energy and the width of these lines were either constant or varied very slightly with temperature. The amplitude of the lines are significantly temperature dependent. The closeness of the temperature at which the amplitudes of these lines reach their minimum to the temperature at which the free-exiton emission is maximum, is an indication of the competition between these two effects  

In this article, a solar absorption chiller used in MehrAbad region of Tehran, Iran is optimized with exergoeconomic principles and genetic algorithm. After optimizing, a storage system with Phase Change Material technique (PCM) is designed for this optimum configuration for supporting system when sunshine is not received adequately, especially at night. Exergoeconomic analysis is based on finding some ways to improving the performance of a thermal system considering economic constrains. In this study, the exergoeconomic optimization is applied for LiBr-water absorption. The results show that total investment cost of main system, the whole of system except storage system, has increased... 

We present the results of a bolometric transition-edge sensor made of a high-Tc superconductor YBCO thin film prepared by fluorine-free metal-organic deposition. The structure of the films was characterized by X-ray diffraction and scanning electron microscopy, and the superconducting properties were determined by R-T measurements. The applicability of the resulting film as an infrared sensor is reported here. The optical response in the range of near infrared and the noise characteristics of the patterned bolometer are measured and analyzed. The dependence of device sensitivity on the bias current and modulation frequency is also investigated. As it is presented in this paper, the results... 

The infrared range optical absorption mechanism of carbon-copper composite thin layer coated on the diamond-like carbon buffer layer has been investigated. By consideration of weak interactions between copper nanoparticles in their network, optical absorption is modelled using their coherent dipole behaviour induced by the electromagnetic radiation. The copper nanoparticles in the bulk of carbon are assumed as a chain of plasmonic dipoles, which have coupling resonance. Considering nearest neighbour interactions for this metallic nanoparticles, surface plasmon resonance frequency (ω 0) and coupled plasmon resonance frequency (ω 1) have been computed. The damping rate against wavelength is... 

Using a generalized Hubbard Hamiltonian, many-electron wavefunctions of negatively charged (NV -) and neutral nitrogen-vacancy (NV 0) centers in diamond were calculated. We report the effect of symmetric relaxation of surrounding atoms on the spin density, calculated from the many electron wavefunctions in the ground and excited states. We evaluated the error, that, arises in estimation of spin density when lattice relaxation effect is neglected in Electron Paramagnetic Resonance experiment and showed that the ground state spin density distribution is accessible in outward relaxations. The computed oscillator strengths give a higher efficiency for the 1.945 eV photoluminescence (PL) line of... 

Ni-Si mixed oxide nanocomposite was prepared by co-precipitation method with Ni(NO 3) 2 ·6H 2O and tetraethylorthosilicate (TEOS) at pH = 10.5 under reflux condition for 6 days. It was then used as a catalyst for the formation of carbon nanotubes (CNTs) by CVD procedure. Characterization of the catalyst and the CNTs was carried out using X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The results showed that Ni-Si mixed oxides nanorods with the average diameter of 3 to 4 nm play a key role in CNTs formation  

Many-body wavefunctions were utilized to calculate von Neumann's entropy as an entanglement measurement for neutral and negatively charged nitrogen vacancy (NV) centers in diamond. A generalized Hubbard Hamiltonian which considers e-e interaction terms completely was used to calculate many-electron wavefunctions of the ground and excited states. Correlation between entanglement and spin density distributed on neighboring atoms of NV is presented. The behavior of spin density and entanglement under relaxations of neighboring atoms is the same for all investigated ground and excited states. The results suggest that the spin density may be used to quantify the entanglemnt and vice versa  

Epitaxial cerium oxide (CeO2) buffer layer has been grown on lanthanum aluminate (LAO) single crystal substrates for fabrication of c-axis oriented YBa2Cu3O7-x (YBCO). Precursor solution of cerium acetylacetonates with viscosity of 0.6 centipoises was spin coated on the 1×1 cm area LAO substrates. The calcination was carried out by very slow ramp (1°C per minute) until the final temperature of 500°C in oxygen flow to remove most of the organic compounds. The final heat treatment has been done at 780°C by a ramp of 20° per minute in gas flow of mixed argon-oxygen with 5 Pa partial pressure of oxygen. The thickness of the deposited CeO2 buffer layer was 20 nm. Then, 100 nm thick YBCO film was... 

Hexagonal array of Cu@CuO core-shell nanoparticles (NPs) on the a-C:H thin film was prepared by codeposition of RF-sputtering and RF-PECVD. The trace of hexagonal NPs supperlattice was recognized by AFM image and XRD result. On the basis of localized surface plasmon resonance (LSPR) of core-shell NPs, the prepared array detected a low flow rate of CO gas at room temperature. XPS results indicate that the surface of Cu@CuO core-shell NPs have no chemical reaction with CO molecule. The physical absorption of CO molecule on the surface of Cu@CuO core-shell NPs increases the LSPR absorbance and causes a red shift in LSPR wavelength. These experimental results are in agreement with Mie theory... 

The main propose of this research is providing a tool for suitable modeling, increase efficiency and decrease construction cost of solar absorption chiller. At first, the solar absorption chiller is modeled by the thermodynamic laws. Then, this model is converted to the new standard mathematical programming model with considering all technical and economic constrains. This mathematical model is optimized by Genetic algorithm (GA). After applying GA, optimized parameters of chiller heat exchanger designing and its electricity consumption are calculated. These parameters consist of heat exchanger effectiveness, heat transfer cross section area, heat transfer coefficient, efficiency of pump and... 

The relationship between unpaired electron delocalization and nearest-neighbor atomic relaxations in the vacancies of diamond has been determined in order to understand the microscopic reason behind the neighboring atomic relaxation. The Density Functional Theory (DFT) cluster method is applied to calculate the single-electron wavefunction of the vacancy in different charge states. Depending on the charge and spin state of the vacancies, at outward relaxations, 84-90% of the unpaired electron densities are localized on the first neighboring atoms. The calculated spin localizations on the first neighboring atoms in the ground state of the negatively charged vacancy and in the spin quintet... 

In this study by Thermal Chemical Vapor Deposition (TCVD) method, the synthesis of carbon nanotubes (CNTs) and temperature affects on the grown CNTs on the NiSio2 catalyst and 304-type stainless steel was investigated. The purification of the grown CNTs on the 304-type stainless steel was also investigated in this study. The synthesis and purification of the samples were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), termogravimetric analysis (TGA) and Raman spectroscopy. Our obtained result by SEM and TEM shows that densities of CNTs growth on the 304-type stainless steel are more than the CNTs growth on the NiSio2 catalyst and both of them have...