Sharif Digital Repository

Fire events and the related toxicants such as CO are responsible for many fatalities in the current century. These hazardous events are much more dangerous when they occur in enclosed spaces. In the present study, a theoretical relation is developed for horizontal distribution of CO in a large tunnel fire. Then, the developed criterion is used to study the effect of some rudimentary parameters such as the heat release rate (HRR) of fire and tunnel's aspect ratio (AR) on CO and temperature stratification. Theoretical results of various heat release rates and aspect ratios for horizontal distribution of CO are compared with numerical results using fire dynamics simulator (FDS5.5). It is found... 

Toxic gases resulted from fire events in subways stations are more dangerous than high temperature radiation from it. So, a well designed smoke exhaust system must be installed in subway station to control the smoke's propagation and discharging. Smoke extraction in subway station depends on the duct laid above the ceiling, so vents are situated in the same level of platform layer's ceiling. If subway station catches fire, smoke will cumulate in smoke reservoirs at the beginning and mechanical fan cannot exhaust any smoke in this process. In This paper, FDS 5.0 is used to simulate smoke's movement in a side platform of an actual subway station in case of a fire. Simulations are carried out... 

The resonant frequencies and torsional sensitivities of an atomic force microscope (AFM) with assembled cantilever probe (ACP) are studied. This ACP comprises a horizontal cantilever, a vertical extension and two tips located at the free ends of the cantilever and the extension which makes the AFM capable of simultaneous topography at top-surface and sidewalls of microstructures especially microgears which consequently leads to a time-saving swift scanning process. In this work, the effects of the sample surface contact stiffness and the geometrical parameters such as the ratio of the vertical extension length to the horizontal cantilever length and the distance of the vertical extension... 

The resonant frequencies and flexural sensitivities of an atomic force microscope (AFM) assembled cantilever probe which comprises a horizontal cantilever, a vertical extension and two tips located at the free ends of the cantilever and the extension are studied. This probe makes the AFM capable of simultaneous topography at top-surface and sidewalls of microstructures especially microgears which leads to a time-saving swift scanning process. In this work, the effects of the sample surface contact stiffness and the geometrical parameters such as the ratio of the vertical extension length to the horizontal cantilever length and the distance of the vertical extension from clamped end of the... 

The resonant frequencies and flexural sensitivities of an atomic force microscope (AFM) with assembled cantilever probe (ACP) are studied. This ACP comprises a horizontal cantilever, a vertical extension and two tips located at the free ends of the cantilever and the extension, which makes the AFM capable of simultaneous topography at top surface and sidewalls of microstructures especially microgears, which consequently leads to a time-saving swift scanning process. In this work, the effects of the sample surface contact stiffness and the geometrical parameters such as the ratio of the vertical extension length to the horizontal cantilever length and the distance of the vertical extension... 

Aerodynamic performance of a Bladeless fan is numerically investigated considering the effect of five geometric parameters. Airflow through this fan was analyzed by simulating a Bladeless fan within a 2 m × 2 m × 4 m room. Analysis of the flow field inside the fan and the evaluation of its performance were obtained by solving conservations of mass and momentum equations for the aerodynamic investigations. In order to design the Bladeless fan an Eppler 473 airfoil profile was used as the cross section of the fan. Five distinct parameters, namely height of cross section of the fan, outlet angle of the flow relative to the fan axis, thickness of airflow outlet slit, hydraulic diameter, and... 

In this paper, a novel analytical approximation to the nonlinear Duffing-harmonic oscillator is presented. The variational iteration method (VIM) is used to obtain some accurate analytical results for frequency. The accuracy of the results is excellent in the whole range of oscillation amplitude variations. © 2009 Elsevier Ltd. All rights reserved  

This research is a numerical analysis exhaustively investigating two-dimensional (2D) transient convective heat transfer in a differentially heated rectangle, possessing sinusoidal corrugated side walls at constant temperatures. The quadrilateral space is filled with a power-law non-Newtonian fluid, plus the right and left walls are uniformly cooled and heated, respectively. The top and bottom walls are retained as adiabatic and the side walls are recast exploiting sinusoidal corrugated shape. The governing equations of the problem are solved using the finite volume method. The evaluation of fluid flow and heat transfer is conducted in such a manner that the power law index n varies from 0.6... 

Similarity solutions are carried out for flow of power law non-Newtonian fluid film on unsteady stretching surface subjected to constant heat flux. Free convection heat transfer induces thermal boundary layer within a semi-infinite layer of Boussinesq fluid. The nonlinear coupled partial differential equations (PDE) governing the flow and the boundary conditions are converted to a system of ordinary differential equations (ODE) using two-parameter groups. This technique reduces the number of independent variables by two, and finally the obtained ordinary differential equations are solved numerically for the temperature and velocity using the shooting method. The thermal and velocity boundary... 

Self-repairing is not an advanced ability of articular cartilage. Tissue engineering has provided a novel way for reconstructing cartilage using natural polymers because of their biocompatibility and bio-functionality. The purpose of cartilage tissue engineering is to design a scaffold with proper pore structure and similar biological and mechanical properties to the native tissue. In this study, porous scaffolds prepared from gelatin, chitosan and silk fibroin were blended with varying ratios. Between the blends of chitosan (C), gelatin (G) and silk fibroin (S), the scaffold with the weight per volume ratio of 2:2:3 (w/v) showed the most favorable and higher certain properties than the...