Sharif Digital Repository

Effect of organoclay (OC) on the performance of styrene-butadiene rubber (SBR)/phenolic resin (PH) blend prepared by two-roll mill was investigated. The influence of OC content ranging between 2.5 and 30 phr on the performance of SBR/PH was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), interfacial energy analysis, tensile, dynamic mechanical, swelling, cure rheometry and thermogravimetric analysis (TGA). It was found that the OC is mainly localized in the SBR phase of SBR/PH blend through the kinetically favored mechanism relevant to rubber chains. The results also demonstrated the positive role of PH on the dispersion of OC. Both PH and OC showed... 

The present study deals with the structure-property relationship of organoclay (OC) filled nanocomposites based on rubber blend comprising of nitrile-butadiene rubber (NBR) and phenolic resin (PH). To obtain a better insight into the characteristics of the NBR/PH/OC hybrid system, a simple model system consisting of NBR/OC nanocomposites is also taken into consideration. A series of NBR/OC and NBR/PH/OC nanocomposites containing a wide range of OC concentrations (2.5-30 phr) are prepared by using traditional open two-roll mill. Structural analysis performed by X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) exhibits mixed exfoliated and... 

Various compositions of maleated ethylene-propylene-rubber (EPR-g-MA) toughened polyamide 6 without and with short glass fiber, i.e. 5-20 wt.% rubber and 5-20 wt.% fiber, are prepared using an industrial twin-screw extruder at different levels of feed rate (100-250 kg/h), screw speed (200-450 rpm) and barrel temperature (230-260 °C). Trial runs designed based on the Taguchi's orthogonal arrays are subjected to tensile, impact, scanning electron microscopy (SEM) and optical microscopy tests; and the results are used to perform the analysis of variance (ANOVA). It is shown that the rubber particle size decreases significantly by increasing the rubber content for the unreinforced blend. The... 

Recently much attention has been paid to the use of low salinity water (LSW) as an enhanced oil recovery fluid. The change observed in recovery factor during LSW flooding is induced from changes in relative permeability and capillary pressure when different levels of salinity are used. However, a few researchers tried to evaluate how macroscopic flow functions depend on the salinity of the injected water. To this end, a series of oil displacement by water was performed on a sandstone rock aged with crude oil in the presence of connate water. The capillary pressure and relative permeability curves are evaluated from inverse modeling of the obtained pressure drop and oil production data. Then,... 

One of the basic challenges during drilling horizontal wellbores is the damage induced by invasion of mud filtrate into the formation. Addition of nanoparticles to drilling fluids has been recognized as a measure of control and reduction of filtrate invasion, which is the primary mechanism of the aforementioned formation damage. Despite notable advances in composing Nano-enhanced drilling fluids, the role of nanoparticle hydrophobicity on performance of the fluids has not been well studied. This study is based on a combined experimental-numerical methodology. In the experimental section, a procedure to find the optimum composition of Nano-enhanced water-based samples, containing... 

Properties of melt processed polyamide 66 (PA66)/multiwalled carbon nanotube composite were first characterized experimentally. The experimental results exhibited the formation of crystalline layer around the nanotubes and a considerable enhancement in mechanical properties by incorporation of multiwalled carbon nanotube up to 1 wt%. Mechanical properties were analyzed in terms of structural parameters using micromechanical models proposed in this study. It was suggested that the mechanical properties were greatly dominated by crystalline layer and nanotube length. It was also deduced that the melt mixing process caused a significant nanotube breakage restricting further enhancement of... 

The present study was an attempt to examine the effects of carbon and cellulose fibers on the tribological characteristics of rubber-based friction materials (RBFMs). A fiber free RBFM as a reference material and a series of fiber included RBFMs at different volume fractions were prepared by two-roll mill. The friction tests were per-formed at different sliding velocities and various drum temperatures. The mechanical properties and surface microstructure of friction specimens were also examined. It was revealed that the carbon fiber infiuences slightly the coefficient of friction (COF) of RBFM but it improves the wear resistance and the fade behavior considerably. It reduces the drum... 

This study deals with the thermal conductivity of rubber-based composite friction materials used in railroad vehicles. Based on a commercially available railroad friction material, called here base material (BM), various friction materials containing different thermally conductive fillers (Cu, brass, Al, Al2O3 and talc) are fabricated and then their thermal conductivities are measured at various contents of the fillers. Addition of the thermally conductive fillers causes an increase in thermal conductivity of the friction material from 0.48 up to 5.8 W/m K, depending on the type and content of the filler. In addition, the experimental results reveal that the thermal conductivity of the... 

Despite extensive studies on electrorefining to remove impurities from copper production units, bleeding electrolytes is the most popular method for controlling impurities due to low operating costs. A controlled cooled-reheat cycle was used to remove impurities in industrial electrolytes of Khatoon Abad copper company. Phase identification and physical study were done by the XRD, SEM, TEM, and FTIR techniques. The results confirmed the possibility of the removal of 23 wt% Ni, 26 wt% Sb, 2.4 wt% As and convention of 6 wt% of As5+ to As3+ at cooled-reheat cycle. © 2022 The Author(s)  

Nanosilica in different grades are used for producing rubber nanocomposites based on natural rubber (NR) and styrene-butadiene-rubber (SBR) blends benefiting from appropriate mechanical properties. This study aimed to introduce recycled nanosilica (RNSiO2) extracted from lead-acid battery separator wastes as a new nanosilica filler to prepare rubber nanocomposites with appropriate mechanical and aging properties in a sustainable manner. Using RNSiO2, vulcanized nanocomposites were prepared based on NR/SBR blends (RT20 and RA20 samples) in the presence of Irganox 1010 as a hindered phenolic antioxidant. An increasing trend was observed in modulus, tensile strength, tear strength, and hardness... 

A single-chip Integrated circuit of 3.3 V/1 W class-D high fidelity and high efficiency audio power amplifier is presented in this paper. The design has been done using a 3.3 V/0.25 /spl mu/m CMOS process. The maximum output power is 1 W before the amplifier saturates. The THD+N at 0.5 W output power is below 0.03% and efficiency is better than 90% thanks to the careful design of the output stage. The dynamic range is more than 100 dB suitable for high fidelity audio applications. A single-loop single-bit third order sigma-delta modulator is used to generate the PWM signal from input audio signal. The PWM signal is then filtered at the output with a second order low pass filter external to... 

Homogeneous and fairly monosized microspherical structures of polyaniline has been synthesized using a simple soft template method with β-naphthalene sulfonic acid (β-NSA) as both the surfactant and dopant, and ammonium persulfate (APS) as the oxidant at 2-5 C. The morphology of PANI-NSA was successfully controlled from nanotubes to microsphere, by changing the synthesis conditions (i.e. pH, the concentration of surfactant and monomer, and temperature). Some mechanistic aspects of the formation of nanotubes and hollow spheres have been discussed precisely based on SEM, TEM, DLS, FTIR and UV-visible results. Moreover, synthesis was performed under acidic environment to obtain further... 

Submicron sized polyacrylamide particles were prepared via modified precipitation polymerization method. Experimental design based on Taguchi approach was employed to study the influence of the polymerization composition including monomer (acrylamide), crosslinker (methylenebisacrylamide), initiator (azobisisobutyronitrile), and modifier (polyvinylpyrrolidone, K-30), on the size and morphology of the particles. Varying the polymerization composition, submicron-particles with sizes ranging between 100 and 600 nm were achieved. In all the cases, polydispersity index (PDI) of the particle size was found to be almost 1 indicating uniformity of the particle size. The concentration of crosslinker... 

A soft template route is reported for the fabrication of polyaniline nanospheres via the oxidative polymerization of aniline in the presence of β-naphthalenesulfonic acid (β-NSA) as both surfactqant and dopant, and ammonium persulfate as oxidant at 2-5°C. Control over the morphology and size of the nanoparticles was achieved by changing the reaction medium via addition of an organic cosolvent (i.e. ethanol or ethylene glycol) and by controlling the concentrations of aniline and β-NSA and the molar ratio of β-NSA to aniline. By this means the size of the β-NSA-aniline micelles and the way that aniline monomer interacts with the micelles were controlled. In fact the lower dielectric constant... 

Incremental launching is a widespread bridge erection technique which may offer many advantages for bridge designers. Since internal forces of deck vary perpetually during construction stages, simulation and modeling of the bridge behavior, for each step of launching, are tedious and time consuming tasks. The problem becomes much more complicated in construction progression. Considering other load cases such as support settlements or temperature effects makes the problem more intricate. Therefore, modeling of construction stages entails a reliable, simple, economical and fast algorithmic solution. In this paper, a new Finite Element (FE) model for study on static behavior of bridges during... 

In the present research, the influence of nanodiamond (ND) and a physical hybrid of ND and fumed nano-SiO2 were investigated on the performance of a typical tire tread compound. The styrene-butadiene rubber (SBR) and cis-butadiene rubber (BR) blend filled with a commercial grade highly dispersive silica at 70 phr loading were used as typical tire tread compound. ND was substituted partially with silica at two different concentrations of 5 and 10phr. Meanwhile, 5 phr of ND/nano-SiO2 hybrids with the weight ratio of 2.5/2.5 and 1/4 were substituted with silica. ND-Filled compounds exhibit increased scorch and cure time compared to controls. Improvement in different characteristics of the... 

A new and general procedure for history matching that uses streamline simulation and a gradual deformation technique has been proposed. Streamline trajectories define the major flow paths and help the algorithm to modify the reservoir model only in the regions that cause the mismatch between simulation results and field observations. The use of a gradual deformation technique enables the algorithm to remain constrained to reservoir geostatistics. It also reduces the number of independent variables in the optimization problem. In our algorithm, effective conductivities are defined along each streamline. The effective streamline conductivities are then adjusted using the values of measured and... 

A highly water stable metal-organic framework (MOF) based on zirconium, i.e. UiO-66, was synthesized and then employed to adsorptive removal of an anionic dye, methyl orange (MO), and a cationic dye, methylene blue (MB), from aqueous solution. In this work, for the first time, the long term stability of UiO-66 in water was investigated for 12 months. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and N2 adsorption/desorption analysis were employed to monitor the textural alteration of UiO-66 during water aging. The results indicated that the structure of UiO-66 was mostly retained and its adsorption capacity toward dyes exhibited minor loss after long term water... 

In this research, UiO-66 and its composite nanoparticles with thermally oxidized nanodiamond (OND) were synthesized via a simple solvothermal method and utilized as solid adsorbent for the removal of anionic methyl red (MR) dye and cationic malachite green (MG) dye from contaminated water. The synthesized adsorbents were analyzed by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA), N2 adsorption–desorption, and zeta potential analyzer. The influences of various factors such as initial concentrations of the dyes, adsorption process time, solution pH, solution temperature and ionic... 

A carboxylate gadolinium-based metal-organic framework (Gd-MOF) is an exceptional candidate for magnetic resonance imaging agents, but its low drug adsorption capacity hinders this MOF from being used as a theragnostic agent. In this work, the Gd-MOF was synthesized by a simple solvothermal method. Then, different activation situations, including various solvents over different time periods, were applied to enhance the specific surface area of the synthesized MOF. Different characterization analyses such as X-ray diffraction and Brunauer-Emmett-Teller along with experimental quercetin adsorption tests were done to study the crystalline and physical properties of various activated MOFs. In...