Sharif Digital Repository

In this paper, the development of a controller for autonomous lateral alignment of fixed-wing Unmanned Aerial Vehicles (UAVs) with runway centerline in landing phase is presented. Fuzzy Logic Control (FLC) is used in order to enable the vehicle to mimic the decision making procedure that a pilot follow in the same situation. Also, for longitudinal motion controller design for the UAV to follow a pre-defined trajectory, the pole-placement technique is used. It is assumed that the runway relative position and orientation are provided by a built in vision system and its associated image processing unit. The performance of the controller in the presence of the Gaussian noises is investigated by... 

This paper proposes a high performance voltage tracking and current sharing among parallel connected inverters by applying optimal control and minimizing the cost function. The control system forces the voltage of load to track the voltage reference, and the current of all inverters becomes equal. Therefore, both current sharing and voltage tracking are obtained. In addition, the smallest input energy and simplicity in control circuit are the other advantages of the suggested method. To show the performance of the proposed control scheme, the simulations with two-modular practical systems are performed and the results are provided. The results indicate that the control objectives are... 

A fuzzy controller has been suggested for attitude control of magnetic actuated satellites in order to calculate the desired mechanical torque based on the attitude error including error in the angles and their rates. The problem of selecting proper magnetic dipole based on the known desired mechanical torque has been investigated, two different methods for the purpose has been suggested and the performance of the attained fuzzy magnetic attitude controllers has been shown under two different simulated conditions. © 2009 IEEE  

Recorded ground accelerations at various locations of Karun III Dam during November 20, 2007, were recorded by an array of accelerometers located on the dam. In terms of amplitude and phase, these accelerations show non-uniformities in different elevations. In this paper, the effect of these non-uniform ground motions on the seismic response of the dam taking dam-reservoir-foundation interaction into account is investigated. The EACD-3D-2008 finite element program and ABAQUS Software are used for carrying out the seismic analyses. For this purpose, time histories of the earthquake accelerations are interpolated at nodal points located on the dam foundation interface. The analysis has been... 

Thermal analysis of Roller Compacted Concrete (RCC) dams is generally carried out considering identical ambient boundary conditions at upstream and downstream faces. For the case of Shahri-Kor Dam (an RCC dam with a height of 57 m), recorded thermal data depicts a considerable difference between upstream and downstream ambient temperatures, especially during cold months. This paper investigates how taking this difference into account can affect the thermal response of the dam. For this purpose, two thermal analyses are carried out with and without consideration of these different ambient boundary conditions (DABC). Consequently, the computed temperatures at representative points are compared... 

The objective of this study was to propose a new analytical model for studying response of head impacts. Head is modeled by fluidfilled ellipsoidal shell of inconstant thickness impacted by a solid elastic sphere. Modeling the head as an ellipsoid is more realistic than modeling it as a sphere, the previous model existing in the literature [3]-[8]. In this model, the effect of Hertzian contact stiffness and local shell stiffness are combined to derive explicit equations for impact duration, the peak force transmitted to head, and the head injury criterion. One of the advantages of the model presented is sensitivity to the site of impact. A comparison between the present analytical results... 

Ultrasound hyperthermia is used to treat tumors in human tissue by heat. It is characterized by the application of high intensity focused ultrasound (HIFU), high local temperatures and short treating time of a few seconds. HIFU is a non-invasive treatment modality for a variety of cancers, including breast, prostate, kidney, liver, bone, uterus, and pancreatic cancers. Computer models have been used to determine tissue temperatures during ultrasound hyperthermia. In this work, we consider a liver tissue with a tumor at its center. We calculated temperature distribution in the presence a large blood vessel. We studied the effect of varying the exposure time (heating duration) and the diameter... 

This work attempts to develop a physical simulation model for the purpose of studying the effect of various design parameters on the performance of a packaged liquid chiller. A computer model which simulates the steady-state cyclic performance of a vapor compression chiller is developed for the purpose of performing detailed physical design analysis of actual industrial chillers. The model can be used for optimizing design and for detailed energy efficiency analysis of packaged liquid chillers. The simulation model takes into account presence of all chiller components such as compressor, shell-and-tube condenser and evaporator heat exchangers, thermostatic expansion valve and connection... 

The purpose of this work is to develop a physical simulation model for the purpose of studying the effect of various design parameters on the performance of a packaged liquid chiller. A computer model which simulates the steady-state cyclic performance of a vapor compression chiller is developed for the purpose of performing detailed physical design analysis of actual industrial chillers. The model can be used for optimizing design and for detailed energy efficiency analysis of packaged liquid chillers. The simulation model takes into account presence of all chiller components such as compressor, shell-and-tube condenser and evaporator heat exchangers, thermostatic expansion valve and... 

We propose and analyze a circularly polarized slot antenna built on a ferrite substrate which is saturated normal to its plane and metalized on both sides. The antenna is built by etching a circular slot in the top metal layer. The antenna operates in the frequency range where the effective permeability of ferrite is negative. An accurate analytical model is derived for the antenna by solving the integral equation for the electric field on the circular slot. The results obtained are in good agreement with numerical simulations. Using the analytical results, a practical antenna is designed that uses a microstrip feed line. For an antenna with inner and outer radii of 4.9 and 5.9 mm, the... 

This paper describes an integrated engineering approach for a mathematical modeling of an automotive air-conditioner system and method for performing heating and cooling load calculations of a vehicle shell assembly for designing an HVAC system for a passenger vehicle. In addition, there is presented a physical optimization technique based on minimization of the total entropy generation for the vehicle air-conditioner and HVAC system. Simultaneous solution of the automotive air-conditioning, air handling and the passenger cabin thermal model provide the transient temperature history for consideration of passenger comfort conditions. The validity of the mathematical model was confirmed using...