Sharif Digital Repository

A nonlinear predictive model controller was designed to control the temperature of a batch polymerization of methyl methacrylate. Using the mechanistic model of the polymerization, a state space model was derived and converted to transfer function model. The coefficients of the transfer function were calculated along the selected temperature trajectory by sequential linearization. 140 operation points were resulted. Model validation showed model ability in process dynamic description. Consequently, DMC algorithm was applied and one objective function was optimized. Results of control loop simulation shows a high precision ability of this algorithm in comparison to classic methods  

Commercial purity copper sheets were subjected to a severe plastic deformation technique known as constrained groove pressing (CGP). The effect of pass number, intermediate and post-annealing on the yield strength, hardness and final microstructure of the copper specimens were investigated. The initial pass increases the strength much more than the subsequent passes. Intermediate and post-annealing up to 300 °C cannot change the mechanical properties significantly and even in some cases improve the strength and hardness while reduce the hardness inhomogeneity. Microstructure after post-annealing at elevated temperatures shows abnormal grain growth. © 2009 Elsevier B.V. All rights reserved  

Control of MMA polymerization batch reactor has intensively investigated. The nonlinear and time varying behavior of the system makes its control a challenging task. MPC algorithm is enjoying an increasing application for control of chemical processes. A sequential linearized model based predictive controller based on the DMC algorithm was designed to control the temperature of a batch MMA polymerization reactor. A genetic algorithm (GA) is suggested to optimize the cost function of DMC. The controller performance was studied via simulation. The controller performance in tracking the profile, noise and disturbances rejection is very good  

Using a mechanical model and dislocation density based model, the evolutions of dislocation density and flow stress of pure copper during constrained groove pressing (CGP) process are investigated. In this regard, the strain and strain rate are achieved from the mechanical model and then input into the dislocation model. To verify the predicted flow stress, the process of constrained groove pressing is performed on the sheets of pure copper from one to three passes. The predicted flow stresses are compared with the experimental data and a good agreement is observed. Also, it is found that during the straining of the copper sheet in CGP process, the dislocation density and strength dropping... 

In the present study, plasma electrolytic oxidation process was carried out on aluminised steel with a pulsed bipolar electrical source at different frequencies, namely, 50, 300, 600 and 1500 Hz with constant 50% duty cycle for 10 min in an alkaline silicate electrolyte. Morphology, wear behaviour and corrosion resistance of the coatings were investigated by scanning electron microscopy, pin on disc and potentiodynamic polarisation experiment in 3·5 wt-%NaCl solution. The results showed that with increasing the pulse frequency, the density of the residual pores increases, but their size as well as the coating thickness decreases. The corrosion current density of the coating processed at 1500... 

Machine learning (ML) is generating new opportunities for innovative research in energy economics and finance. We critically review the burgeoning literature dedicated to Energy Economics/Finance applications of ML. Our review identifies applications in areas such as predicting energy prices (e.g. crude oil, natural gas, and power), demand forecasting, risk management, trading strategies, data processing, and analyzing macro/energy trends. We critically review the content (methods and findings) of more than 130 articles published between 2005 and 2018. Our analysis suggests that Support Vector Machine (SVM), Artificial Neural Network (ANN), and Genetic Algorithms (GAs) are among the most... 

Transdermal drug delivery systems have overcome many limitations of other drug administration routes, such as injection pain and first-pass metabolism following oral route, although transdermal drug delivery systems are limited to drugs with low molecular weight. Hence, new emerging technology allowing high molecular weight drug delivery across the skin—known as ‘microneedles’—has been developed, which creates microchannels that facilitate drug delivery. In this report, drug-loaded degradable conic microneedles are modeled to characterize the degradation rate and drug release profile. Since a lot of data are available for polylactic acid-co-glycolic acid (PLGA) degradation in the literature,... 

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only... 

One of the most important obstacles in passive radar applications is removing the direct signal from the target channel. Otherwise, week echoes from the targets in the target channel would be ignored due to the limited dynamic range of the system. One of the most effective techniques in this field is using adaptive filters. In this paper various adaptive filters are introduced and their performances are shown and compared