Sharif Digital Repository

Embedded real-time systems have limitations on power consumption, mainly due to battery usage and temperature constraints. In addition, a large part of these systems has timing constraints. These constraints should be considered when we use power management techniques. Nowadays, due to the use of fault-tolerance techniques, power consumption and especially peak power consumption are increased so it can miss Thermal Design Power constraint. Recently, due to the conservative design of TDP for chips, it is not considered, and hence, a new power constraint as Thermal Safe Power is defined for thermal and power characteristic of the system. The purpose of this study is to define an optimization... 

The human brain is the most sensitive and important human organ and surgery must be done with high precision and without risk. During surgery, brain tissue deform continuously due to gravity, out of the cerebrospinal fluid and the changing pressure of the cerebrospinal fluid and the surgical maneuvers. Because the surgeon has no direct view on brain internal, the ways to solve this problem is to pay attention. This method makes it possible to the surgeon see in the brain and the brain tissue deformation. This thesis method is based on biomechanical modeling. After forming finite element model from the pre-operative MRI, brain surface and volume datasets during surgery as a load, apply to the... 

In this work, design and construction of copper vapor and Cu Br laser is explained. By special design of copper electrodes the average power from Cu laser system was increased more than 20% in comparison to the same system with expensive electrodes made from molybdenum. However, the basic goal of this work was the construction of CuBr laser. Based on the home made fast trigger unit for Hydrogen thyratron, operation of the manufactured system was possible up to 25 kHz. By using special designed copper electrodes very uniform operation of CuBr plasma diluted in Ne gas was observed. By tuning of the laser parameters such as gas pressure, exciting voltage and pulse repetition rate, from 9 Cm3 of... 

Distributed feedback dye lasers are among the suitable candidates for spectroscopic applications due to their capability of producing widely tunable picosecond pulses in UV-IR region. However, the pulsewidth sensitivity of the laser to pump intensity fluctuations hinders its suitability for precision applications. In this thesis, by utilizing widely used Self Q-Switching model, we showed that if the dye solution is pumped by a narrow (sub-nanosecond) pulse, the laser can operates in the single-pulse output mode with a better stability over a wide range of pump intensity. After that, we used a dynamical model based on the induced polarization and Maxwell equations, where the obtained results... 

The present thesis investigates the surge phenomenon of high speed centrifugal compressors. Surge is a highly undesired condition and may cause severe damage to the machine and thus the plant. Traditionally, surge is avoided via a surge avoidance scheme wih recycle valve in discharge at the most common approach. A one dimensional technique is developed where the Greitzer lumped parameter model along with the Gravdahl one dimensional model is considered as the basis. Shaft dynamics, volume dynamics, losses, energy transfer and time lag are imbedded in the present model to improve the prediction of the compressor characteristics beyond the stability region. On the other hand, in order to... 

Axial compressor design is a very complex and expensive process. In general, for design and development of a new axial compressor, manufacturing companies usually intend to employ an existing and successful axial compressor as an starting point and modify and upgrade it. In this regard, dimensional scaling is a common method for derivative axial compressors. The goal of dimensional scaling is to get a different capacitywhile minimizing the development time and cost. In this thesis, theNASA eight stage transonic axial flow compressor is chosen as the base model for dimensional scaling to lower and upper size of its original dimension. The scaled compressor is analyzed with a quasi 2-D code.... 

The purpose of this research is theoretical and numerical investigations on centrifugal compressor. A computer code has been developed to simulate single-zone and two-zone model, based on the revised formulation for real gas, using Peng-Robinson equations. Single-zone modeling, also known as meanline method, established based on 1-D equations of fluid dynamics considering ideal gas relations, empirical loss correlations, slip factors, impeller efficiency and no wake or separation regions. Considering usual significant separated regions in the gas path of impellers, two-zone (jet and wake zone) model has been developed to achieve a more reliable simulation by using fewer correlations based on... 

In this research, the principles of design of Heat Exchangers in thermoacoustic systems are developed. The Heat Exchangers as a essential part of thermoacoustic systems, complete the thermodynamic cycle in these systems. In this thesis, principles and algorithms of design for Shell&Tube, Plate and Screen Heat Exchangers are described and these principles are validated for each kind of Heat Exchangers. Then the balance of exergy is studied in thermoacoustic systems and at the end, for every Heat Exchangers amount of exergy destruction is evaluated for oscillating and non-oscillating fluids. Based on fitness functions of exergy destruction, heat transfer area and acoustic pressure drop, Heat... 

Compression systems are widely used in industry. Dynamic Modeling is a necessary step in design procedure of a safe compression system. A dynamic model should be adequate and simulate dominant elements of system. One important element of industrial compression systems is downstream pipelines. In this work, a dynamic model including pipeline acoustics is developed. It is accepted that changes of working gas molecular weight can cause inception of instabilities in compression systems. The dynamic model used to study mechanisms of these instabilities. A conventional control system is modeled and tuned for the compression system. The ability of this control system to prevent such instabilities... 

thermoacuostic heat pump (THP) is One of the most important thermoacuostic applications which is used for heat lost recovery in industrial applications and civil applications.In this project, we have a quick review on thermoacuostic theory and researches in this field. Also a thermoacuostic heat pump in a lab scale will be designed and analyzed.For achieving this goal, first, mathematical equations of thermoacuostic systems are reviewed; a thermoacuostic heat pump is designed on the base of Tijani method and final model is validated by DeltaEC software. In the next step, after investigating about laboratory equipments which is used in testing process, we generate test matrix and study about... 

Typical thermoacoustic systems deal with the conversion of heat energy to sound energy and vice versa. Recent advances in the field of thermoacoustics have altered the working mechanism of many conventional heating and cooling devices. These systems have three highlighted advantages: first, they have simple structure, no moving parts, low cost of manufacture, and high reliability; second, by using inert gases as working fluid, they are environmentally friendly; and finally, heat driven thermoacoustic devices can be driven by low quality energy sources such as waste heat and solar energy.
The main focus of the present thesis is on the application of the thermoacoustic technology in the... 

Streaming has some applications in medical and industrial science. This phenomena can increase or decrease efficiency of an acoustic system. Deliberate streaming used to eliminate heat exchanger is an example of desired applications. In the most cases, secondary flow is an undesired issue. Streaming in thermal buffer tube (TBT) of thermoacoustic stirling heat engine (TASHE) has some unwanted effects. The main goal of author is to simulate numerically periodic field in TBT with axisymmetric geometry and study the effects of variating geometry and turbulence on the intensity of streaming. According to inaccessible boundary conditions in TBT of TASHE, firstly, the field is numerically solved... 

Considering the multi-disciplinary aspects as well as the importance of a wide performance map of a propulsion system, this thesis is focused on the preliminary design aspects of an axial flow pump with an inlet guide vane. First, a one-dimensional design algorithm is developed. The code is used to perform a preliminary design of a prototype pump. The results are used to carry on a detailed 3D design by using commercial software. The obtained geometry and performance map are compared with available data. Finally, the finalized code is employed to design and analyze a one megawatt axial pump with and without inlet guide vanes