Sharif Digital Repository

InAlAs/InGaAs/InP high electron mobility transistors have higher mobility comparing to structures without indium. But existence of indium causes smaller Eg and as a result smaller breakdown voltage. However, increasing percentage of indium results in higher mobility and as a result higher current and transconductance. Therefore decreasing percentage of indium causes higher breakdown voltage at the sometime lower transconductance. One of the most important parameters that limit maximum output power of transistor is breakdown voltage. In this paper, InAIAs/InGaAs/InP HEMTs with different structures are simulated and a structure with a good transconductance and breakdown voltage is introduced  

Based on the closed-form solution of a one-dimensional wave equation, the primary, secondary and acoustic feedback paths for the active control of sound in an acoustic duct have been investigated. Accurate models for the condenser microphone and loudspeaker, which include both the electro-mechanical and mechano-acoustical couplings as well as acoustical damping, have been considered. A generalized form of the filtered-x least mean square (FXLMS) algorithm that uses a more general recursive adaptive weight update equation to improve the performance of the FXLMS algorithm has been developed. Computer simulations were carried out to investigate the performance of acoustical feedback and... 

The exact closed-form solution of a one-dimensional wave equation including the viscous damping effect has been obtained from the Green's function. Accurate models for the error sensor and secondary loudspeaker, which includes the electro-mechanical and mechano-acoustical couplings, have been used and the transfer function of the primary, secondary and acoustic feedback paths of the active noise control system have been obtained. The generalized form of the classical FXLMS algorithm, referred to G-FXLMS algorithm, has been developed. In contrast to the FXLMS algorithm, G-FXLMS algorithm does not neglect the time shift of the filter coefficients and employs a more general recursive adaptive... 

The single-reference/multi-output active noise control (ANC) of an accurate physical model of an acoustic duct system has been investigated. Computer model of a multi-channel ANC system with tonal and sweep sine input signals, and an adaptive feedforward algorithm that minimizes the generic cost function are developed. Results obtained for various single-input/single-output (SISO) configurations of ANC systems were compared. The dynamic response of a single-reference/multi-output ANC system, using Minimax and MEFXLMS algorithms, is studied and the effect of acoustical feedback neutralization in a multi-channel ANC system is studied. Simulation results demonstrate that the multi-channel... 

The use of adaptive feedforward controllers has proven to be a very successful strategy for controlling noise and vibration in a variety of applications. One reason is that the feedforward controller is an open loop controller, which can be designed to cancel the undesired noise in one position with any accuracy. However, the feedforward controller requires an input signal, called a reference signal, correlated to the noise source. As a consequence, a single reference controller can only reduce noise radiated from a single noise source. In many applications, there is a need to attenuate noise produced by several noise sources. In this paper, three different structures, single, modulating and... 

Dynamic and stability analysis of non-uniform Timoshenko beam under axial loads is carried out. In the first case of study, the axial force is assumed to be perpendicular to the shear force, while for the second case the axial force is tangent to the axis of the beam column. For each case, a pair of differential equations coupled in terms of the flexural displacement and the angle of rotation due to bending was obtained. The parameters of the frequency equation were determined for various boundary conditions. Several illustrative examples of uniform and non-uniform beams with different boundary conditions such as clamped supported, elastically supported, and free end mass have been... 

The growing rate of population and technological advancement have led to an increase in natural resource consumption, which has caused irreparable damage to the environment. The implementation of green supply chain management is one of the most effective ways to deal with environmental degradation. Therefore, in this paper, a bi-objective mixed integer linear programming model is developed to design a green supply chain network. In the proposed model, the possibility of customer storage, being faced with shortage, locating of distribution centres, green vehicle routing problem, split delivery, multi-depot vehicle routing problem (VRP), capacitated VRP, and uncertainty in demands will be... 

Supplier selection is an important and challenging problem in sustainable supply chain management. We propose a dynamic decision support system (DSS) for sustainable supplier selection in circular supply chains. Unlike the linear take-make-waste-dispose production systems, circular supply chains are nonlinear make-waste-recycle production systems with zero-waste vision. The proposed DSS allows users to customize and weight their economic, social, and circular criteria with a fuzzy best-worst method (BWM) and select the most suitable supplier with the fuzzy inference system (FIS). Machine learning is used to maintain and synthesize the criteria scores for the suppliers after each supplier... 

Supplier selection is an important and challenging problem in sustainable supply chain management. We propose a dynamic decision support system (DSS) for sustainable supplier selection in circular supply chains. Unlike the linear take-make-waste-dispose production systems, circular supply chains are nonlinear make-waste-recycle production systems with zero-waste vision. The proposed DSS allows users to customize and weight their economic, social, and circular criteria with a fuzzy best-worst method (BWM) and select the most suitable supplier with the fuzzy inference system (FIS). Machine learning is used to maintain and synthesize the criteria scores for the suppliers after each supplier... 

In the eld of supply chain, selecting a suitable green supplier could signi cantly help us decrease the cost and risks of the operations and increase the quality of green supply. This paper develops an integrated two-stage approach based on Fuzzy Analytic Hierarchy Process (FAHP) and multi-objective mixed-integer linear programming to select suppliers and allocate order in the green supply chain. In the rst stage, suppliers are evaluated using FAHP method and in the second stage, a multi-product multi-period supply chain is developed considering green location-routing problem, discounting, and time window under uncertainty. Then, a fuzzy solution approach is applied to solve the proposed... 

The increasing level of customer awareness and application of environmental laws by governments, on the one hand, and the increasing number of competitors, on the other hand, has obliged industry owners to include green activities in the design of the supply chain network. Green activities include any type of action that reduces environmental degradation. Hence, this study seeks to develop a bi-objective, mixed integer linear programming (MILP) model for designing a green supply chain network. In the proposed model, the minimisation of costs and detrimental environmental effects are discussed. LP metric method is used to solve the bi-objective model and the proposed model is run by using... 

Maximizing the value of resources and producing less waste are strategic decisions affecting sustainability and competitive advantage. Sustainable closed-loop supply chains (CLSCs) are designed to minimize waste by circling back (repairing, reselling, or dismantling for parts) previously discarded products into the value chain. This study presents a novel two-stage fuzzy supplier selection and order allocation model in a CLSC. In Stage 1, we use the fuzzy best-worst method (BWM) to select the most suitable suppliers according to economic, environmental, social, and circular criteria. In Stage 2, we use a multi-objective mixed-integer linear programming (MOMILP) model to design a...