Sharif Digital Repository

In the present study, the thermal behavior of human teeth during laser radiation has been discussed. The high laser power, as well as its low emission, can allow deviations from the Fourier heat transfer model. To overcome this problem, the non- Fourier heat transfer method, dual phase lagged (DPL), has been used. Wisdom considered in this study to evaluate the thermal behavior of tooth. Using the finite volume method, the DPL equations are solved and the thermal response of the teeth is obtained during laser irradiation. The effect of delay times, which are the parameters of the DPL model and depart from the Fourier model, is fully demonstrated on the temperature behavior of the tooth, and... 

In the present work, the behavior of flow inside the pressure-swirl atomizers (PSA) is studied by the numerical simulation. The pressure-swirl atomizer is widely used in many industrial applications such as fuel injection in gas turbine, internal combustion engine and liquid-fuel rocket, spray drying, spray in firing and agricultural nozzles.
The flow simulation inside the injector (PSA) deals with many complicated considerations due to air core formation in the axial zone of the injector as well as high tangential and axial velocities in the swirl chamber. The two phase flow is modeled by level set methods in the pressure swirl atomizer. Moreover, the explicit algebraic Reynolds stress... 

The objective of this project is numerical simulation of air flow and heat transfer between two horizontal concentric cylinders with rotation of inner cylinder and inertia of outer cylinder grooves on the inner cylinder. In this study, the air, meanwhile rotational motion by the inner cylinder will enter into the annular space between two cylinders with certain flow rate. It can be mentioned to cooling of power plant generators, Electric motors and rotating machines among usages of air flow between two cylinders. In this article the objective is calculation of pressure drop and Nusselt number, temperature distribution on the inner cylinder under conditions of constant temperature of... 

In this project, direct numerical simulation of fluid flow inside the porous channel is carried out. The flow channel is containing uniform array of solid blocks with square cross sections in an staggered scheme. Two thermal boundary conditions of constant temperature and constant heat flux of solid blocks were applied to the problem. The Navier-Stokes equations directly applied to the fluid region with no assumption of volume-averaging. Governing equations of two-dimensional flow with constant properties were discretized with control volume method. Energy equations for solid and fluid phases were solved separately. The results show that for solid block lengths over channel height, a/H=0.05,... 

In the present study, Nano-fluid natural convection on a constant temperature vertical plate is numerically investigated, following the similarity analysis of transport equations. After changing the governing differential equations to the ordinary differential equations, they were numerically solved by the fourth order Runge-Kutta method.. The analysis shows that all three main profiles, velocity, temperature and concentration in their specific boundary layers, and the Prandtle number, depend on three important additional dimensionless parameters, namely a Brownian motion parameter, a thermophoresis parameter, and a buoyancy ratio parameter. Finally, it was found that the Nusselt number in... 

In the leading thesis, an attempt is made to improve the evaporation rate by emphasizing the reduction of heat transfer to the fluid bulk. In this study, inspired by the process performed in plants in the transfer of water from the roots to the leaves and especially the function of plant vessels, a kind of evaporator-improving surface was designed. The general function of this surface is to prevent the heat radiated to the surface of the water from being spent on heating the fluid deep in the water, and by concentrating this heat in a thin layer of fluid on the surface, the rate of evaporation increases. This surface consists of three parts: evaporative layer, insulation and water suction... 

The main goal of this thesis is the design and development of a rehabilitation device for helping patients “to improve blood circulation” & retain and recover their abilities if possible that were lost during the stroke or a accident like that (my research in karaj/iran shows that it is possible by just movement of the specific body part). The focus is on hand in this thesis because Injuries to the hand are common and can be very debilitating since our hands are our primary means for interacting with our world. For rehabilitation in case of human hand there are several practices that should be done for patients either in home or in a rehabilitation center, time and money that is supposed to... 

In the past few decades, shaking tables are widely used to evaluate system response of structures under seismic excitations. These devices are used without any fundamental research performed on a shaking table system as an entity model. In most of these studies for simplicity, it is assumed that there exist no considerable vibration and displacement around the shaking tables, and no attention is paid to the peripheral substances such as soil settled under the foundation.
In this thesis, result of ambient vibration test on shaking table system (solid deck, concrete foundation and soil layer) has been presented. Precise sensors known as low frequency and high accuracy accelerometers have... 

Out of several ground improvement techniques available, stone columns have been widely used. This technique has been successfully applied to increase the bearing capacity and to reduce the settlement for foundation of structures like liquid storage tanks, earthen embankments, raft foundations, etc., where a relatively large settlement is permissible. This technique has, generally, been proven successful in increasing the stiffness of weak soils, upgrading their safe bearing capacity, and reducing their total and differential settlements, as well as speeding up their consolidation process. The beneficial effects of stone column installation in weak deposits is manifested in the form of... 

Laminar forced convection flow through a channel partially filled with a porous material was numerically studied in this thesis. The Navier-Stokes and Brinkman-Forchheimer equations were used to model the fluid flow in the free and porous regions, respectively. Coupling of the pressure and velocity fields was resolved using the SIMPLEC algorithm. The local thermal equilibrium was adopted in the energy equation. The effects of the thermal conductivity ratio, Darcy number, porosity, Reynolds number and height of the porous insert on velocity and temperature field were investigated. The results show that the flow behavior and its associated heat transfer are susceptible to the variation of the... 

In the present study, a new version of haptic devices is presented in which user’s hand is in contact with the device just while collision with virtual surface. In this system, the position of user’s finger can be traced by using a camera and the haptic device follows user’s finger at the distance of about two centimeters. While the haptic device approaches to the virtual surface, gradually reduces its speed and stops about two centimeters distant of virtual plane. Then user’s hand collides with the haptic device which is static. Greater fidelity, transparency, more stability and also no need to large actuators are of the advantages of this system. In this project, first we present a new... 

In this thesis we try to find optimized parameters for imaging and manipulation of a biosample with AFM. For this we have prepared a numerous Molecular Dynamics simulation and find some reliable result. So, first we have focused on imaging process in Non contact mode (the less harmful mode). Then we headed into the manipulation process. The main problem about manipulating a biosample is the environment. In imaging section, the process of imaging a biomolecule by AFM is modeled using molecular dynamics simulations. Since the large normal force exerted by the tip on the biosample in contact and tapping modes may damage the sample structure and produce irreversible deformation, the non-contact... 

Results of previous studies on silt and clay indicated that variations in the small strain shear modulus, Gmax, during drying had a non-linear increasing trend with matric suction with greater values upon wetting. However, due to different material properties and inter-particle forces, different behaviour in Gmax is expected for sand. Although considerable research has been devoted in recent years to characterize the behaviour of Gmax of sand during drying, rather less attention has been paid to the effect of hydraulic hysteresis on Gmax and its variations during wetting. In the study presented herein, an effort was made to characterize the variation of Gmax for specimens of sand during...