Sharif Digital Repository

In this investigation, the behavior of pin loaded composite plates is studied numerically. A failure prediction model is used to predict the ultimate strength considering three different mechanisms of failure: bearing, shearout and net tension. The model consists of two major parts: stress analysis and failure analysis. The main difference between this investigation and others is considering more realistic assumptions in modeling of the problem. As an example, we consider nonlinear behavior in the shear stress/ shear strain relationship of each unidirectional ply and use this model in optimization problem to reach maximum strength. The results are compared with experimental results available... 

In this thesis the shear strength of pipe shear connector is investigated experimentally and numerically. The numerical analysis uses a nonlinear finite element model of the push-out specimen. The specimens consist of the pipe shear connector, steel beam, concrete slab and embedded steel rebar for concrete confinement. Eight push-out specimens are constructed with different pipe sizes and concrete strength. The results are used in a finite element parametric study to evaluate the strength of such connectors for all practical ranges of pipe size and concrete strength. It is shown that pipe connectors are more effective in transferring shear forces than angle and channel and stud connectors.... 

Structural health monitoring (SHM) has been motivated in aircraft and civil industries over the two last decades. Ultrasonic guided wave propagation technique is one of the best damage detection methods in airplane thin wall structures because of their large distance traveling and low attenuation.
In fact by efficient design of sensors pattern one can effectively pick up the changes that happen in propagated signals due to presence of any kind of structural damage. This could be effectively achieved by numerical simulation techniques like finite element modeling. To obtain a damage detection algorithm based on instantaneous baseline data, here, finite element technique is employed for... 

In this study, novel algorithms are presented for nonlinear parameter varying systems with uncertainty in the model predictive control using heuristic algorithms. To this end, some algorithms are developed which provide the possibility of estimating simultaneously states and control signal of the stochastic nonlinear systems. Then, the model predictive control algorithm is presented for stochastic nonlinear systems with uncertainty to estimate uncertainty and compensate it using ant colony optimization. Next, the model predictive control algorithm is developed for nonlinear system with matched bounded uncertainty using particle swarm optimization. Performance of the developed controllers is... 

Considering the unique characteristics of aluminum alloys in the 5XXX series, such as high strength-to-weight ratio and corrosion resistance, as well as the absence of precipitation hardening, composite fabrication using these alloys has garnered attention. Consequently, friction stir additive manufacturing (FSAM), a novel solid-state layering technique, has been proposed for manufacturing components from these alloys, avoiding the drawbacks associated with traditional melt-based additive manufacture methods. The objective of this research is to produce a five-layer 20mm composite wall in the aluminum 5754 substrate using iron powder via FSAM to achieve desirable mechanical properties. To... 

In recent years, requirement engineering and goal modeling have gained more attention among different organisations. Therefore, different methods have been designed to discover stakeholders’ requirements and translate them into process and organizational goals. Various goal models have been introduced to represent these goals and their relations towards each other. Still, these methods are manual representations of different process scenarios and do not relate to the actual behavior. In 2014, Map Miner Method (MMM) was introduced to discover intentional process models from event logs. MMM uses Hidden Markov Model (HMM) as a means to represent the process as a map model of strategies and... 

Recommending routes to city taxis in order to improve their performance in finding passengers can reduce traffic, pollution and waiting time for passengers, as well as this, increasing the efficiency of taxis can increase their income. In this study, by analyzing trajectory data obtained from 536 taxis in San Francisco over a period of one month, we generated networks of cells, each of which has time-dependent characteristics such as the probability of finding a passenger, the capacity of each cell, or the amount of demand exists is in the cell and the average speed of passing through that cell. also, the connections between these cells in order to make more use of the experiences of taxi... 

The debate over political philosophy has resurfaced five decades after the publication of John Rawls' famous book on the theory of justice. In that book, Rawls criticizes perfectionist states, And considers a state just that leaves the perfection and goodness of human beings to the citizens themselves. And the state can not be the final arbiter and interferor in the good and perfection of the citizens, and the state should never be one-sided in this conflict between the various opinions of the people about the good. Therefore, the state should only provide the means for citizens to be able to pursue their good deeds freely and equally, which is what Rawls calls the precedence of the right... 

The purpose of the present study is to develop neural network estimation method for hybrid or panel data which have a combination of two cross-sectional and time series structures and because of the features of both structures, their use in different sciences offers many advantages; and the analytical methods for this data structure are also different from other one-dimensional structures, so different and specific regression models are presented for this data structure. However, in the artificial neural network method, modeling the development for this data structure is neglected, so in the present study, using the concepts of panel regression methods and their application to the... 

To capture what is really done on the computer, we have decided to simulate the behavior of an Intel processor based computer. The main part of a computer is its CPU, so we are have simulated the Intel processors from 8086 to Pentium with MMX, SSEX and 3DNow. To work with hardware and software and going back to these steps for several times, is a time consuming procedure. To avoid falling in such loops, one way is to simulate the hardware and develop the software according to this simulation. This remedy solves time consuming procedure since changing hardware in simulation is quite easy. To simulate the digital systems, we need to have the software codes of the processors. Since the Intel... 

One of the utmost important factors during salvage operation of drowned ships is raising velocity. Uncontrolled raise is a dynamic phenomenon which can lead to the sudden tensions, collapse in airbags or ships. Studing this issue helps the engineers which kinds of problems are more important during salvage operations. This study focus on modeling and analysis of raising movment of the ship with FLOW-3D and ABAQUS software.
In FLOW-3D environment, hydrodynamic analysis of rising movment of drowned ship has been done. We should mention that applied forces and velocities and other parameters from the FLOW-3D output should be passed IMCA Criteria to avoid uncontrollable raise. In ABAQUS... 

Profile Monitoring is a new research topics in the field of statistical process control. In many applications of statistical quality control, sometimes quality of a process or product described by a relationship between a response variable and one or more independent variables.The researchers call this relationship profile. The study seeks to demonstrate that monitoring profiles In addition, the industry can be effective in medical field and improves control of the patient's condition by a doctor. Profiles are usually modeled with a linear regression equation, non-linear or polynomial. finally, the results of this study, using actual data, models and methods to predict and control... 

Two experimental models were designed and tested to extract energy from vortex induced vibrations of a elastically mounted one degree of freedom rigid cylinder in the Reynolds range of 120000 < Re <220000. In the first model the amplitude and frequency of the movement was measured then a second model was designed to be tested in the Emam Hossein marine laboratory. The model was designed in a way that many of its properties like mass ratio, spring constant and damping coefficient were able to be altered. In this study the vortex induced vibration of an elastically mounted cylinder was scrutinized in high Reynolds and very low mass ratios for the first time and an amplitude ratio of 2.49 were... 

As a method of cancer treatment or improvement of cancer-related complications, external radiation therapy is prescribed by physicians, in case of detection of a tumor in a region of patient’s body. Over time, various techniques have been developed for external beam radiation therapy. Among which, Intensity Modulated Radiation Therapy (IMRT), due to its ability to adjust the intensity of radiation beams, has a higher capacity to generate appropriate dose distribution based on tumor size and volume and it is one of the most widely used techniques in cancer treatment centers.The core process in treatment planning is using appropriate computer algorithms which results in posing enough damage to... 

Supplier selection and order quantity allocation problem is one of the most complex making decision problems comes into account. In the past, supplier selection done based on criteria such as price, quality and delivery time. Today's supply chains with the aim of expanding business activities and improving their performances, Follow process such as outsourcing, product development, and selection of multi-supplier strategies. This conditions will bring opportunities and threats for supply chains. One of the possible risks to supply chains are disruption risks and disruption has been a great concern in the past decade and disruption of suppliers are one of the new topics that have recently... 

At the present, End-stage renal disease(ESRD) is the ninth-leading cause of death in the USA.according methods of medical treatment for End-stage renal disease (ESRD), transplantation is the most viable renal replacement therapy for ESRD patients, there is a disparity between the demand for kidneys for transplantion and the supply. Incompatible inblood-type and antigen matching between patient-donor pairs is cause of shortage in disparity between the demand and the supply.paired kidney exchange of kidney among incompatible patient-donor pairs.PKE can be solve many difficulties in matching patient with incompatible donors. Kidney transplant surgeries in PKE must take place simultaneously...