Sharif Digital Repository

In optimum designing of wireless power transfer(WPT) coils, maximum efficiency and maximum power transfer capability of coils should be considered. In this paper, a novel technique for optimum design of WPT coils based on maximum efficiency with considering required power transfer capability has been given. Optimum selection of system parameters including coil and wire dimensions, number of turns of coils and compensation capacitor selection based on minimum weight of copper mass is also given. For evaluation purpose a 100W experimental sample is designed and tested in 20cm range  

Stable control of water level of drum is of great importance for economic operation of power plant steam generator systems. In this paper, a linear model of the boiler unit with time varying parameters is used for simulation. Two transfer functions between drum water level (output variable) and feed-water and steam mass rates (input variables) are considered. Variation of model parameters may be arisen from disturbances affecting water level of drum, model uncertainties and parameter mismatch due to the variant operating conditions. To achieve a perfect tracking of the desired drum water level, two sliding mode controllers are designed separately. Results show that the designed controllers... 

Pt@Bi-TiO2 photocatalysts with different Bi (0–5 wt%) and Pt (0–2 wt%) contents were prepared by a two-step sol-gel and photo-deposition technique and were used in photo-reduction of CO2. The synthesized catalysts were characterized by X-ray powder diffraction (XRD), UV–Vis diffuse reflectance spectroscopy (DRS), scanning and transmission electron microscopy (SEM and TEM), nitrogen sorption measurement (BET), Raman spectroscopy, Electron paramagnetic resonance (EPR) spectroscopy and photoluminescence spectroscopy (PL). CO2 photo-reduction results revealed that the introduction of Bi into TiO2 structure and subsequent loading of Pt on its surface significantly increased the methane yield.... 

A traveling wave distributed mixer is studied. It is shown that increasing the drain-source capacitances in a distributed FET mixer simultaneously improves its conversion gain and noise figure. Besides, it is shown that proper loading of input and output elements can improve the device performance. The simulation results are well matched with the measurements and also with the results of the existing certified simulators. © 2002 IEEE  

Let (Formula presented.) be a graph of order (Formula presented.) and size (Formula presented.). Suppose that (Formula presented.) is a function such that (Formula presented.). In this paper we provide a criterion for (Formula presented.)-choosability of (Formula presented.). Using this criterion, it is shown that the choice number of the complete (Formula presented.)-partite graph (Formula presented.) is (Formula presented.), which is a well-known result due to Erdös, Rubin and Taylor. Among other results we study the (Formula presented.)-choosability of the complete (Formula presented.)-partite graphs with part sizes at most (Formula presented.), when (Formula presented.), for every vertex... 

Tape mechanisms must be able to transport the tape with a constant velocity for achieving high rate of data transfer. In this paper, a multivariable model of tape transport mechanism including the take-up and supply reel servos for tape tension control and capstan servo for speed control is considered. To achieve desired performance,pole-placement approach based on general canonical control form (GCCF) is used. Instead of using expensive tension sensors, an observer is designed. A regulator system is developed for disturbance rejection; and a modified integral control is designed for perfect tracking of desired setpoints in tape speed and tensions. Since the real dynamic model associates... 

Tape mechanisms must be able to transport the tape with a constant velocity for achieving high rate of data transfer. In this paper, a multivariable model of tape transport mechanism including the take-up and supply reel servos for tape tension control and capstan servo for speed control is considered. To achieve desired performance,pole-placement approach based on general canonical control form (GCCF) is used. Instead of using expensive tension sensors, an observer is designed. A regulator system is developed for disturbance rejection; and a modified integral control is designed for perfect tracking of desired setpoints in tape speed and tensions. Since the real dynamic model associates... 

Reference trajectory management is a method to modify reference trajectories for the faulty system. The modified reference trajectories define new maneuvers for the system to retain its pre-fault dynamic performance. Controller reconfiguration is another method to handle faults in the system, for instance by adjusting the controller parameters (coefficients). Both of these two methods have been considered in the literature and are proven to be capable of handling various faults. However, the comparison of these two methods has not been considered sufficiently. In this paper, a controller reconfiguration mechanism and a reference trajectory management are proposed for the spacecraft attitude... 

To achieve a good performance of a boiler-turbine unit, dynamic variables such as steam pressure, water level of drum and electric output of turbine must be controlled. In this paper a nonlinear model of the boiler-turbine unit is considered in which the inputs are the valve positions of fuel flow, steam control, and feed-water flow. Using two control methods, feedback linearization and gain scheduling, a PI controller is designed. It is shown that by applying both methods, system goes from one operating point to another with an appropriate specification of time response. Results show that system with a controller designed based on gain scheduling method has a better time response from a... 

A graph G is called an Mr(k)-graph if G has no k-list assignment to its vertices with exactly r vertex colorings. We characterize all A 3(2)-graphs. More precisely, it is shown that a connected graph G is an A3(2)-graph if and only if each block of G is a complete graph with at least three vertices  

Due to the nonlinear dynamics of hydraulic systems, applying high performance closed-loop controllers is complicated. In this paper, a single-rod hydraulic actuator is considered in which load displacement (for positioning purposes) is controlled via manipulation of the input voltage to the servo-valve. Dynamics of the servo-valve is described by first and second order transfer functions (named as Models 1 and 2). Through linearization of the system around its operating points, dynamics of the hydraulic actuator is represented in the state space. A full-order observer is designed for on-line states estimation. Then, feedback control system is designed for both regulation and tracking... 

Dynamic vibration absorbers are used as semi-active controllers to reduce the undesirable vibrations in many applications such as electrical transmission lines, helicopters, gas turbines, engines, bridges and etc. One type of these absorbers is tunable vibration absorber (TVA). In this paper, regenerative chatter in an orthogonal turning process is suppressed using a (TVA). It is shown that TVA can modify the frequency response function of the cutting tool so as to improve cutting stability in turning process. In addition, tool wear is an important factor which works as a positive damping and helps the chatter suppression beside exertion of the TVA. Finally, using the SIMULINK Toolbox of... 

One of the important challenges in the auto industry is to reduce the mass of the vehicle while meeting structural performance requirements for Crashworthiness, Noise, Vibration and Harshness (NVH) etc. In this paper, a multidisciplinary optimization (MDO) of a car back-bonnet is investigated by using trie Response Surface Method (RSM). Firstly, a car body is fully surface modeled in CATIA and meshed in HYPERMESH software. Then, modal analysis of the finite element model is performed by NASTRAN software to find natural frequencies. Frequency map of that component is extracted and compared with a reference map to detect defects. Design of Experiments (DOE) methodologies is used for a... 

Implanted biomedical sensor networks provide a major application of sensor networks in the near future. Their high temperature due to wireless communication, might damage the surrounding tissues. This paper presents an efficient thermal-aware routing. Our proposed protocol states that when some nodes in the shortest path have a high temperature, ignores this path. The simulation results indicate the superiority of the proposed method compared to other thermal-aware routing protocols in terms of reducing temperature without a significant increase in packet delivery delay and power consumption of nodes. © 2009 IEEE  

Dynamic vibration absorbers are used as semi-active controllers to reduce the undesirable vibrations in many applications such as electrical transmission lines, helicopters, gas turbines, engines, bridges and etc. One type of these absorbers is tunable vibration absorber (TVA). In this paper, regenerative chatter in an orthogonal turning process is suppressed using a (TVA). It is shown that TVA can modify the frequency response function of the cutting tool so as to improve cutting stability in turning process. In addition, tool wear is an important factor which works as a positive damping and helps the chatter suppression beside exertion of the TVA. Finally, using the SIMULINK Toolbox of... 

Self-excited and forced vibrations are important topics in machining processes because their occurrence results in poor surface finish, increase in tool wear and hampers productivity. In this paper, turning process is modeled as a SDOF dynamic system including quadratic and cubic structural nonlinearities. The effect of tool flank wear, as a contact force between the work-piece and tool, is addressed vigorously. Multiple scale method is used to find the solution of the nonlinear dynamic equation including regenerative chatter, forced excitation and tool wear. It is shown that, width of cut can be considered as the bifurcation parameter of the system. Primary, super-harmonic and sub-harmonic... 

One of the important challenges in the auto industry is to reduce the mass of the vehicle while meeting structural performance requirements for crashworthiness, noise, vibration and harshness, etc. In this paper, a multidisciplinary optimisation of a car back-bonnet is investigated by using the response surface method. A car body is fully surface modelled in CATIA and meshed in software. Then, modal analysis of the finite element model is performed by NASTRAN software to find natural frequencies. A frequency map of that component is extracted and compared with a reference map to detect defects. Design of experiments methodology is used for a screening of the design space and for the... 

Reducing the burden of the remaining actuators through decreasing the performance gracefully is an important field in active fault tolerant control. According to the literature, two important points have been identified in the works considering graceful performance degradation: 1) using single-objective optimization, 2) assuming an engineering insight into the performance of the faulty system. This paper has two contributions: First, it is shown that in some cases, single-objective optimization may not be able to provide a satisfactory solution for the problem. Second, a new systematic and general method is proposed to remove the need for the engineering insight. The proposed method is based... 

Graphene nanoplatelets (GNPs) are ideal reinforcements for improving the mechanical properties of aluminum-based matrices due to their outstanding properties. However, it essentially depends on their uniform dispersion in the matrix. In this study, the challenge of uniform dispersion of graphene was performed by functionalizing the non-covalent surface and sonication of GNPs applying non-ionic polymeric ethyl cellulose (EC) surfactant, in which a colloidal mixture was provided with Al powder and graphene, followed by sintering at 620 °C and consolidation. The density and mechanical properties of nanocomposite specimens were investigated and compared with a non-surfactant-assisted Al/GNP... 

Dynamic vibration absorbers are used to reduce the undesirable vibrations in many applications such as electrical transmission lines, helicopters, gas turbines, engines, bridges and etc. One type of these absorbers is tunable vibration absorber (TVA) which can act as a semi-active controller. In this paper, by applying a (TVA), chatter vibration is suppressed during boring process in which boring bar is modeled as a cantilever Euler-Bernoulli beam. The optimum specifications of absorber such as spring stiffness, absorber mass and its position can be determined by developing an algorithm based upon mode summation method. Finally, using the SIMULINK Toolbox of MATLAB, the analog simulated...