Sharif Digital Repository

We studied dynamics of droplets inside channels under surface forces created by chemicalsteps on the channel walls. A multi-component Shan-Chen lattice Boltzmann method isused for this purpose.The effects of parameters such as the channel height, viscosity anddensity ratios on the results were investigated for homogeneous and grooved substrates. Alsoan analytical solution was developed for droplets under chemical heterogeneities in channels with smooth surfaces. The solution considers a general condition, namely, asymmetry of the contact angles on the top and bottom walls, the viscosity of the gas as the second fluid and the effect of the channel height. Then using Shan-Chen lattice... 

In this research, droplet motion in symmetric and asymmetric junctions in micro and nano scales was investigated. Droplets motion in symmetric and asymmetric junctions have many applications in many industries such as chemical and pharmacy. In this research symmetric T-junction in micro and nano sizes was simulated numerically in 2D and 3D formes. Also asymmetric T-junction (with unequal width branches) was simulated numerically in two cases, 2D and 3D. In the asymmetric T-junction, also an analyrical theory was developed. Numerical simulation was performed by using VOF techniqe and analytical theory was developed by thin film theory. For verifying the accuracy of numerical solution, grid... 

Mesoscopic hydrodynamic equations are solved employing a VOF based method to investigate the equilibrium shape of nanodroplets positioned over various topographic geometries of the supporting substrate for three-dimensional systems. By taking into account liquid-liquid and liquid-solid interactions a complex distribution for inter-molecular forces over the substrates (the disjoining pressure) is observed. In this research we show that motion of nanodroplets not only caused by contact angle difference in drplets two sides, but also depend on disjoining pressure parameters.Geometries with increasing complexities, from wedges to three dimensional edges and wedges, were explored with the main... 

This research concerns investigating the behavior of two-phase flow in the inlet and outlet of the microchannels.Both the droplet based and the continuous microfluidics are considered. For the continuous system whenthe minor fluid enters the microchannel, due to ratio of viscosity of two fluids, viscous folding occurs.Viscous folding phenomena is similar to the buckling phenomena in solids.This means that the viscosity of the fluid, which is applied to two sides of the fluid layer, causes folding the fluid layer and changing the shape of it. For the study we employ a VOF based numerical routine. In order to verify numerical results, the grid and the time step independenciesare checked. In... 

Hydrodynamic mesoscopic equations are solved using boundary integral method to investigate the coarsening dynamics of two dimensional nanodroplets. The dynamics is probed by locating two drops on homogeneous, chemical heterogeneous and physical heterogeneous substrates respectively. For homogeneous substrate, the effect of different parameters like droplets distance, slip boundary condition, surface contact angle and disjoining pressure type on the dynamics is studied. Results reveal that increasing the contact angles to values larger than a critical value may qualitatively change the coarsening process and the profile of the disjoining pressure can appreciably modify the coarsening rate.... 

A droplet placed on the boundary of two solids with different wettabilities will move to the more wettable part. This is a well-known phenomenon and has been extensively used in a variety of processes and applications ranging from biological systems and ink jet printing to the commercial lab-on-a-chip. Because of its importance, many studies are conducted around this phenomenon. The difference between the equilibrium contact angles of the droplet on the two parts gives rise to an interfacial driving force which moves the droplet. Such a motion is not continuous as the droplet slides to the more wettable area, the driving force diminishes and consequently the droplet stops. A non-stop motion... 

In modern era, standpoints about atrium design have been revolutionized. In modern architecture, atrium not only designed for illuminating purposes but also designed by natural ventilation and passive cooling policies. Numerous parameters are making role in thermal efficiency of Atrium. A couple of these parameters are Atrium shape and openings area. In high rise atria the lower level rooms enjoy the advantage of buoyancy-driven ventilation while the upper level rooms suffer from its lack or weak presence. One strategy to solve this problem is designing building with various opening area in different heights but manipulating the opening size is restricted by some facts. Excessive Opening’s... 

Ethylene process is one of the most complex systems in petrochemical industries.The first section of the ethylene plant is the cracking furnace.The radiant section of predicted olefin furnaces is symmetrical with respect to a plane through the center line of the furnace and at an angle of 90° with the side walls. There are a total of 24 vertical radiant coils located centrally in the firebox wherein, bottom andside wall burners supply the heat necessary. Each four coils known as a ZONE so, as a result there are six zones, called zone A through F. Failures(rapture, creep, material degradation) rate on the coils decreases from zone A to zone F (A, B, C, D, E and F) respectively.From... 

Water transportation through carbon nanotubes is key for designing nanodevices. The directed transport of water molecules through a rotating charged carbon nanotube (CNT) is investigated by molecular dynamics simulations. It is found that the net flux of continuous unidirectional water flow depended sensitively on the charge distribution, charge density and rotation of the CNT. we find that for a constant charge density, the water flux increases with the increase of the charge difference. Besides, we find that the water flux shows a nonlinear dependence on the angular velocity of the rotation. The rotation of the CNT with low angular velocities, can not generate a continuous water flux. The... 

Investigation of transport and deposition of aerosol particles has been of interest to researchers in many branches of science. Various numerical and experimental methods has been utilized in particulate fluid flows studies. In recent relevant researches lattice Boltzmann method has been widely used and is reported to be a robust and efficient method. In present study, numerical investigation of dispersion and deposition of aerosol particles is studies in the channel, containing elliptical obstacles geometry using Lattice Boltzmann Method. Fluid flow simulations are performed using LBM while for the study of particle transport and deposition, tracking and the motion equations of them,... 

Drag reduction on surfaces always has been a great case of study, especially in transport industry. This project discusses the external laminar flow of a single-phase fluid over a flat plate and the effects of making rectangular tiny grooves - in micron or millimeter - on them to reduce total drag. Making grooves with appropriate geometry on surfaces causes the fluid-solid contact area on the groove's surface turn into fluid-fluid and as a result the fluid will not shed into the groove. In other words the flow instead of having a no-slip boundary condition on inner surfaces of the groove, creates vortices in them that causes a remarkable reduction in velocity gradient followed by a skin... 

The formation of droplets at a T-junction in a micro channel network is primarily influenced by the pressure difference across the interface in the squeezing regime. Accurate measurements of droplet velocity and pressure profiles are difficult to obtain experimentally, yet these are the basic parameters required. Droplet micro fluidics has shown great potential for biological assays, chemical reactions and polymer emulsions. High stability allows the droplets to work as stable and isolated reactors that open up for parallel and serial reactions where each droplet can be screened individually. The purpose was to fabricate such systems, establish stable droplet generation where droplet volumes... 

In recent years carbon nanotubes and other carbon nanostructures such as graphene sheets have attracted a lot of attention due to their unique mechanical, thermal and electrical properties. These structures can be used in desalination of sea water, removal of hazardous substances from water tanks, gases separation, and so on. The nano porous single layer graphene membranes are very efficient for desalinating water due to their very low thickness. In this study, the mechanism of passing water and salt ions through nano porous single-layer graphene membrane are simulated using classical molecular dynamics. In the simulation, in order to separate salt ions from the water, the effects of applied...