Sharif Digital Repository

In this article, the synthesis of magnetite nanostructures was successfully carried out by the sonochemical process. In this method, stoichiometric amount of iron chlorides (FeCl3.6H2O and FeCl2.4H2O), ammonia (NH3) and polyvinylpyrolidone (PVP) were used to synthesize pure Fe3O4 nanoparticles. The effect of initial sonication power of the ultrasonic device on the size and morphology of the final products as one of the effective parameters was investigated. For this, the initial power of the sonicator was evaluated at 90, 70, 50 and 30 W at 40°C. Characterization of Fe3O4 nanoparticles was done by transmission electron microscope (TEM) and X-ray powder diffraction (XRD) and its magnetic... 

Self-propagating exothermic reactions during mechanical milling of FeCl 3/CoCl 2 mixture together with sodium seeds resulted in formation of Fe 50Co 50 nanoparticles. Highly exothermic reactions resulted in temperature raise and formation of Fe 50Co 50 phase within the first 5min; however Fe 50Co 50 single-phase was obtained after 30min of milling. The products were characterized by XRD, SEM, EDS, TEM and VSM. Obtained results showed that both milling time and NaCl salt matrix affected the size, morphology, microstructure and magnetic properties of the produced particles  

In this study, the effect of adding 5–12.5 wt% CuO to TiO2 on photocatalytic properties of the nano-composite TiO2/CuO was investigated. The products were characterized by X-ray diffractometer, SEM, Brunauer–Emmett–Teller (BET), and DRS. BET-specific surface area of the TiO2/CuO composites was lower than that of the pure TiO2. Incorporation of CuO into TiO2 shifted absorption spectra to the visible region. As the CuO content increased from 0 to 12.5%, a clear decrease in optical band gap from 2.95 to 2.30 eV was observed. The photocatalytic performance was determined by methyl orange degradation and cyanide photo-oxidation under ultraviolet irradiation. However, the excessive incorporation... 

Photocatalysts that are used for waste water treatment are often suspended in the waste water during processing and then must be removed from the water after treatment. To reduce the post-degradation expenses and time, separation is facilitated by an immobilization process. The effect of immobilized TiO2 geometries on the photocatalytic behavior of the photocatalyst is investigated in this work. Powder, fiber, film, and network-shaped TiO2 nanocatalysts were produced by using different templates. The cellulose fiber and ceramic templates were used as substrates for fiber and film/network geometry production. The products were characterized by x-ray diffraction (XRD),... 

In this work, the effect of addition of ZrO2 to TiO2 and catalyst geometry on photocatalytic properties of the nanocomposite TiO2/ZrO2 was investigated. The traditional use of powdery photocatalyst for the degradation of organic compounds has post-treatment problems which means much higher time and costs. A novel method to minimize these problems is immobilization by insertion onto an inert substrate. Several geometries of TiO2–10%ZrO2 (T-10Z) nano-photocatalysts (powder, fiber, film, and network-shaped) were produced using different templates. The products were characterized by X-ray diffraction, field emission scanning electron microscopy, Brunauer–Emmett–Teller, and diffuse reflectance... 

In typical photocatalytic processes slurry reactors are used in which catalyst particles have to be separated from the solution after the process ends which means much higher time and costs. Hence, immobilizing process is carried out on the catalyst to overcome this problem. In this work, fiber and network geometries were produced by particle precipitation on substrates. The obtained structures were characterized by XRD, SEM, and Brunauer–Emmett–Teller analyses. Photocatalytic performance of the samples was investigated by methyl orange degradation and also by hydrogen generation from water/methanol splitting. From the SEM images, the size range of the TiO2 particles in the network... 

Introduction: The COVID-19 pandemic has considerably affected human beings most of whom are healthcare workers (HCWs) combating the disease in the front line. Methods: This cross-sectional study aims to explore the effects of stress and anxiety caused by COVID-19 on the quality of sleep and life in HCWs, including physicians, nurses, and other healthcare staff. In this global study, we asked 1,210 HCWs (620 and 590 volunteers from Iran and European countries, including Germany, the Netherlands, and Italy, respectively), who age 21–70, to participate in the test. Several measures of COVID-related stress, anxiety, sleep, and life quality, including the 12-item General Health Questionnaire... 

Four 5-, 10-, 20- and 30-story moment frames, representing low-, mid-, and two high-rise structures, were subjected to a great number of idealized directivity pulses. The amplitudes and periods of pulses vary from 0.02 g to 1.0 g and 0.5 to 12 sec, respectively. Over 1400 nonlinear dynamic analyses of low- to high-rise moment frames were performed which were feasible through using modified fish-bone model. The distribution of interstory drift along the height was studied and two applied contours were proposed: (i) the maximum interstory drift contour, and (ii) the critical story contour. These contours were demonstrated versus the ratio of natural period of the structure to the pulse period... 

In this article singular points of a parallel manipulator are obtained based on a novel geometrical method. Here we introduce the constrained plain method (CPM) and some of its application in parallel mechanism. Given the definition of constraint plane (CP) and infinite constraint plane (ICP) the dependency conditions of constraints is achieved with the use of a new theorem based on the Ceva geometrical theorem. The direction of angular velocity of a body is achieved by having three ICPs with the use of another theorem. Finally, with the use of the above two novel theorems singularities of the 3UPF_PU mechanism are obtained. It should be emphasized that this method is completely geometrical,... 

An analytical model is proposed to study the effect of particle size on melting enthalpy and entropy of metallic nanoparticles (NPs). The Mott's and Regel's equations for melting entropy in the combination of core average coordination number (CAC) and surface average coordination number (SAC) of freestanding NPs are considered. Clusters of icosahedral (IC), body centered cubic (BCC), and body centered tetragonal (BCT) structure without any vacancies and defects are modeled. Using the variable coordination number made this model to be in good agreement with experimental and molecular dynamic (MD) results of different crystal structures. The model predicts melting entropy and enthalpy of... 

Grinding is widely used for manufacturing of components that require fine surface finish and good dimensional accuracy. In this study a thermo-mechanical finite element analysis is conducted to find out how grinding parameters can affect temperature and residual stress distribution in the workpiece. Results of parametric study presented in this work indicate, by carefully selecting the grinding parameters, minimum thermal and mechanical damage can be achieved. Higher workpiece velocities produce higher surface residual stress. By increasing depths of cut, depth of tensile residual stresses increases. Convection heat coefficient does not have any considerable effect on surface residual stress... 

Adaptive Noise Cancellation (ANC) is a well-known technique for background noise reduction in automobile and vehicular environments. The noise fields in automobile and other vehicle interior obey the diffuse noise field model closely. On the other hand, the ANC does not provide sufficient noise reduction in the diffuse noise fields. In this paper, a new multistage post-filter is designed for ANC as a solution to diffuse noise conditions. The designed post-filter is a single channel Linear Prediction (LP) based speech enhancement system. The LP is performed by an adaptive lattice filter and attempts to extract speech components by using intermediate ANC signals. The post-filter has no... 

Self-Compacting Concrete (SCC) is a unique type of concrete that can flow and fill spaces without the need for vibrating compaction, resulting in a dense and uniform material. This article focuses on estimating the compressive strength of SCC utilizing Artificial Neural Networks. Specifically, the study employs multilayer perceptrons with back-propagation learning algorithms, which are commonly used in various problem-solving scenarios. The study covers essential components such as structure, algorithm, data preprocessing, over-fitting prevention, and sensitivity analysis in MLPs. The input variables considered in the research include water, fine aggregate, super-plasticizer, fly ash, coarse... 

Seismic retrofits can significantly reduce the vulnerability of masonry buildings. Multiple seismic retrofit alternatives are often available for a given building. Estimating the cost of each candidate action is essential to selecting and implementing the appropriate seismic retrofit initiatives. This research harnesses the capabilities of various regression models for cost estimation. A dataset from 167 retrofit projects for masonry school buildings was used to develop models. Three main retrofit actions were taken into consideration: shotcrete, steel belt and fiber-reinforced polymer. Various regression methods, including multiple linear regression, ridge regression, lasso regression, and... 

Shot peening is widely used to improve the fretting fatigue strength of critical surfaces. Fretting fatigue occurs in contacting parts that are subjected to fluctuating loads and sliding movements at the same time. This paper presents a sequential finite element simulation to investigate the shot peening effects on normal stress, shear stress, bulk stress and slip amplitude, which are considered to be the controlling parameters of fretting damage. The results demonstrated that among the modifications related to shot peening, compressive residual stress has a dominant effect on the fretting parameters  

One-dimensional (1D) MgO structures were successfully synthesized via carbothermic reduction of mechanically activated mixture of MgO and graphite. Mechanical activation of source materials before carbothermic reduction can substantially enhance the formation of MgO products at a temperature (1000 °C) relatively lower than that required in previous approaches (≥1200 °C). However, the morphology of MgO formed is dependent on the degree of mechanical activation and the condition of the subsequent carbothermic reduction. Two distinctive morphologies were found for MgO products synthesized using our method: single crystalline nanorods with rectangular cross-sections whose diameters range from 50... 

Attitude and vibration control of a general form of flexible satellites is addressed in this paper. Partial differential dynamic equations are derived considering new details such as multi sectioned solar panels and elastic connections between main hub and solar panels. Boundary control approach is adopted to eliminate simplification errors of discrete models, using just one actuator in the hub. Asymptotic stability of attitude dynamics is proved for a group of boundary controllers and necessary conditions for asymptotic stability of vibrations are discussed. Being independent of modeling accuracy and using easily measurable feedbacks are among advantages of the proposed class of... 

Characterization and calcination behavior of a low-grade manganese ore, as a part of Mn ferroalloys production, was studied by XRF, ex-situ XRD, in-situ XRD, and SEM-EDS techniques. Calcination experiments were carried out at and up to 900 °C (1173 K) in air and argon atmospheres. The samples were in particles and powder forms. The results indicated that both quartz and calcite phases in the ore exhibit a bimodal spatial distribution; as relatively large regions and finely distributed in the Mn- and Fe-containing phases. By Rietveld analysis of the in-situ XRD data, the reactions occurring upon heating during the calcination process were deduced. Thermal decomposition and reactive diffusion...