Sharif Digital Repository

In this work, the phenomenon of dynamic strain aging in a high carbon steel is studied and different initial microstructures including fine and coarse pearlite structures are considered. Tensile tests at different temperatures and strain rates are performed to evaluate the occurrence of dynamic strain aging and mechanical properties as well as to calculate apparent activation energies for onset and termination of dynamic strain aging. The results show that dynamic strain aging occurs for both microstructures while the initial microstructures alters the activation energies for appearance and termination of this phenomenon. The microstructural studies illustrate that a combination of cementite... 

In this paper, a thermo-mechanical model has been used to predict the temperature history and residual stress distribution in gas tungsten arc welding of AA5251 plates. This model has also been utilized to estimate the residual stresses under different welding sequences, while in the model the effect of temperature on material properties were taken into account. In order to verify the predictions, residual stresses within the welded samples and weld pool geometry were experimentally measured employing hole drilling and macro-examination of weld cross-section, respectively. The comparison between numerical and experimental data shows a reasonable agreement. The predictions show that the... 

The purpose of this work is to assess the effect of welding fixtures on distributions and values of residual stresses during Gas Tungsten Arc Welding (GTAW). The butt-joint GTAW of AA5251 plate is investigated using a transient thermo-mechanical analysis performed by the finite element program, ABAQUS. The model considers two different welding conditions including unconstrained and perfectly constrained conditions while macro examination and residual stress measurements by implementing hole drilling techniques are utilized to evaluate the predictions. The results show that the utilizing of a welding fixture alters the temperature field within the plate being welded and the depth of the weld... 

This study concentrates on the effects of weld sequence and welding fixtures on distribution and magnitude of induced arc welding residual stresses built up in butt-joint of Gas Tungsten Arc Welding (GTAW) AA5251 plates. Aluminum plates have been welded under different welding conditions and then, longitudinal and transverse residual stresses were measured in different points of the welded plates employing hole-drilling technique. The results indicate that welding sequence significantly alters the distributions of both longitudinal and transverse residual stresses while the changing in the weld sequence leads to 44% decrease in longitudinal residual stress. Besides, both the geometry of weld... 

A three-dimensional model is utilized to predict temperature distribution and fluid flow during the process of gas tungsten arc welding (GTAW). In order to evaluate the effect of the heat flux model on the accuracy of predictions, two types of heat sources - with different natures based on Gaussian surface heat flux and volumetric Goldak's double-ellipsoid heat flux distributions - are taken into account. These heat flux schemes are input into a model simulation of GTAW of AA1050. In the next stage, the transient temperature distribution within the metal being welded is predicted for each heat flux model using FLUENT computational fluid dynamics software. The fusion and heat-affected zones... 

In this work, thermo-mechanical behavior of an aluminum alloy during gas tungsten arc welding (GTAW) is studied using a three-dimensional mathematical model. The model can be employed to determine residual stresses and their distribution after the welding operation. The effects of the strain hardening and the temperature dependency of material properties have also been considered in the calculations. Model validation has been performed using experimental measurements of residual stress by means of hole-drilling technique. The measurements have been carried out at the heat affected zone (HAZ) and base metal next to the welding line. In addition, microstructural observations have been made to... 

As computer simulation increasingly supports engineering design, the requirement for a computer software environment providing an integration platform for computational engineering software increases. A key component of an integrated environment is the use of computational engineering to assist and support solutions for complex design. In the present paper, an integrated software environment is demonstrated for multi-disciplinary computational modeling of structural and geotechnical problems. The SUT-DAM is designed in both popularity and functionality with the development of user-friendly pre- and post-processing software. Pre-processing software is used to create the model, generate an... 

In this paper, the influence of powder-tool friction on the mechanical properties of the final product is investigated in pressing metal powders. A computational algorithm is presented for simulation of frictional contact in the compaction process of powder. The large deformation finite element (FE) formulation is characterized by the use of penalty approach in which a plasticity theory of friction is incorporated to simulate sliding resistance at the powder-tool interface. The constitutive relations for friction are derived from a Coulomb friction law. A double-surface cap plasticity model is employed together with the nonlinear contact friction behavior in numerical simulation of powder... 

In this paper, an atomistic–continuum homogenization multiscale method is developed to study the nonlinear behavior of heterogeneous nanomaterials. The atomistic representative volume element (RVE) with vacancy and/or void defects are analyzed by employing the fully atomistic method, in which the nucleation, migration, and elimination of dislocation, as well as the dislocation-vacancy interaction, are captured. The coarse-scale material domain is modeled within the framework of the nonlinear finite element method, and the impression of nanoscale material defects is investigated by upscaling the stress tensor and tangent modulus from the atomistic RVE based on the Hill-Mandel principle. The... 

In this paper, a new criterion for passivity of haptic devices is obtained. This criterion creates a relationship between Coulomb friction coefficient, viscous friction coefficient, sampling rate, and the maximum simulated stiffness. The process of derivation of the passivity criterion is described in detail. This criterion is improved compared with other existing criteria and predicts passivity in haptic rendering more accurately. In particular, for speeds of less than 5 cm/s, the new passivity criterion should replace the previous criteria to avoid unwanted vibrations of stiff virtual walls. Analytical and numerical investigations are presented to validate the new criterion. A specific... 

The field emission properties of MoO2 nanostars grown on a silicon substrate and their emission performance in various vacuum gaps are reported in this article. A new structure of molybdenum oxides, named a nanostar, is grown by thermal vapor deposition with a length of ̃1 μm, a thickness of ̃50 nm, and its width in the range of 500-700 nm. The morphology, structure, composition, and chemical states of the prepared nanostars were characterized by scanning electron microscopy, high-resolution transmission electron microscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). According to XRD analysis, the grown nanostructures are composed of both crystalline Mo4O11 and... 

Several exoskeletons with various configurations and degrees-of-freedoms (DOFs) have been introduced in the literature, but not many have addressed the optimal selection of the mechanism's DOFs. In the proposed system a semi-passive toe joint is introduced to achieve several advantages. The performance of the proposed novel passive toe joint is evaluated experimentally. In addition, the semi-passive abduction/adduction DOFs in the hip joint and eversion/inversion DOFs in ankle joint is proposed to facilitate turning while providing more comfort during normal walking. The effect of passive DoFs existence on the user comfortability is studied with the aid of three kinematic indices. In the... 

This paper models the dielectric corona pre-ionization, capacitor transfer type of flat-plane transmission line traveling wave transverse excited atmospheric pressure nitrogen laser by a non-linear lumped RLC electric circuit. The flat-plane transmission line and the pre-ionizer dielectric are modeled by a lumped linear RLC and time-dependent non-linear RC circuit, respectively. The main discharge region is considered as a time-dependent non-linear RLC circuit where its resistance value is also depends on the radiated pre-ionization ultra violet (UV) intensity. The UV radiation is radiated by the resistance due to the surface plasma on the pre-ionizer dielectric. The theoretical predictions... 

The reliability Studies are done in order to determine the probability of functioning or availability of different engineering systems. These studies can also provide a basis for comparing different structures of a system and can be used as a tool to improve the system design. Also, reliability is an important consideration in the planning, design and operation of transit system. Since the issue of the reliability of electric vehicles has not been sufficiently and seriously evaluated yet, so in this paper, the reliability of the various types of these kinds of vehicles will be discussed and then the reliability indices of them will be compared with each other and with the conventional cars  

Considerable interest in the indoor applications of wireless local-area networks (WLANs) demands some powerful simulation methods of these systems. Proper modeling of the physical propagation channel is crucial in this context. A novel simulation method for indoor wideband multi-input multi-output (MIMO) channel at the operating frequency band of IEEE 802.11a, HIPERLAN/2, and the emerging IEEE 802.11n standards is presented in this paper which is suitable for performance analysis of MIMO techniques in these systems. The presented model is developed on the basis of a previously proposed channel representation at the same frequency band. Simulation results for MIMO channel capacity are... 

To synthesize a novel biopolymer-based superabsorbent hydrogel, 2-acrylamido-2-methylpropanesulfonic acid (AMPS) was grafted onto kappa-carrageenan (KC) backbones. The graft copolymerization reaction was carried out in a homogeneous medium and in the presence of ammonium persulfate (APS) as an initiator, N,N,N',N'-tetramethyl ethylenediamine (TMEDA) as an accelerator, and N,N'-methylene bisacrylamide (MBA) as a crosslinker. A proposed mechanism for KC-g-AMPS formation was suggested and the hydrogel structure was confirmed using FTIR spectroscopy. The affecting variables on swelling capacity, i.e., the initiator, the crosslinker, and the monomer concentration, as well as reaction temperature,... 

In this work, a comparative study of hybrid solar cells based on P3HT and TiO2 nanofibers was accomplished. Electrospinning, a low cost production method for large area nanofibrous films, was employed to fabricate the organic-inorganic hybrid solar cells based on poly (3-hexylthiophene) and TiO2 nanofibers. The performance of the hybrid solar cells was analyzed for four density levels of TiO2 nanofibers which resulted in the average power conversion efficiency of about 0.0134% under AM 1.5 simulated illuminations (100 mWcm-2). It is found that the higher densities of TiO2 lead to more interface area and generating exciton, so the power conversion efficiency will be increased till the active... 

Forming limit diagram is often used as a criterion to predict necking initiation in sheet metal forming processes. In this study, the forming limit diagram was obtained through the inclusion of the Marciniak–Kaczynski model in the Nakazima out-of-plane test finite element model and also a flat model. The effect of bending on the forming limit diagram was investigated numerically and experimentally. Data required for this simulation were determined through a simple tension test in three directions. After comparing the results of the flat and Nakazima finite element models with the experimental results, the forming limit diagram computed by the Nakazima finite element model was more convenient... 

Radial forging and indentation forging processes are two processes used for sizing and/or internal profiling of tubes. In this paper, the two processes are simulated using finite element method and their results are compared with Experimental results. The purpose of this paper is to compare the pattern of residual stresses in both processes. Copyright © 2005 SAE International