Sharif Digital Repository

In this paper, a combination of in-situ chemical synthesis and electrolysis methods was applied for the preparation of zinc oxide/graphene oxide quasi core-shell nanoparticles. Pure zinc oxide was also prepared using the same method at different temperatures. 100 °C was selected for synthesizing the ZnO/GO quasi core-shell (zinc oxide as a core and few layers of graphene oxide as a shell). The particle size was 15 ± 2 nm in all samples. In both processes, oxygen was the main reason for the connection between the core and the shell. XRD patterns also confirmed the formation of ZnO (with regular wurtzite structure) and ZnO/GO quasi core-shell structures. Raman spectroscopy results confirmed... 

In this study, the replacement of hydrogen with ammonia in a laboratory Moderate or Intense Low-Oxygen Dilution (MILD) burner is being investigated by incorporating air swirling to study NOx formation in the flow field. A CH4/H2/NH3 fuel jet is modeled using the RANS (Reynolds-Averaged Navier-Stokes equations) approach for various fuel mixtures with ammonia content ranging from 0% to 18%, while maintaining a constant methane concentration. The study is conducted under two conditions: axial coflow with hot diluted air and swirled with the swirl numbers of 0.6–1.0. The hot oxidizer consists of 9% O2 and 6% O2 at 1300 K. The combustion model is based on the eddy dissipation concept, and a... 

Commercially pure aluminum sheets, AA 1050, are processed by accumulative roll bonding (ARB) up to eight cycles to achieve ultrafine-grained (UFG) aluminum as primary material for mechanical testing. Optical microscopy and electron backscattering diffraction analysis are used for microstructural analysis of the processed sheets. Strain rate sensitivity (m-value) of the specimens is measured over a wide range of strain rates by stress relaxation test under plane strain compression. It is shown that the flow stress activation volume is reduced by decrease of the grain size. This reduction which follows a linear relation for UFG specimens, is thought to enhance the required effective (or... 

The microstructure and phase transformational behavior of NiTi-based composites reinforced with 6 wt.% of α-alumina nanoparticles have been investigated. Two kinds of starting materials, elemental Ni–Ti and prealloyed austenitic NiTi, were used to prepare the composites. The samples were consolidated using a hot isostatic pressing method. The X-ray diffraction results showed that while unreinforced NiTi mainly contained B2 phase at room temperature, martensitic B19′ phase appeared in the microstructure after addition of the α-alumina nanoparticles. The differential scanning calorimetry measurements indicated that the martensitic transformation temperatures were elevated in the composite... 

We studied the flow stress and microstructural changes of nanostructured Al-6063 alloy produced by mechanical alloying at various temperatures and strain rates. The analysis of flow curves was performed by a constitutive equation, and the stress exponent and activation energy were determined as functions of strain. The deformation mechanisms were elaborated through microstructural observations by electron backscattering diffraction and transmission electron microscopy. Coarsening of the subgrains and grain growth upon deformation was monitored and related to the Zener–Hollomon parameter  

Ultrafine-grained (UFG) Al6063 alloy reinforced with 0.8 vol% nanometric alumina particles (25 nm) was prepared by reactive mechanical alloying and direct powder extrusion. Transmission electron microscopy and electron backscatter diffraction analysis showed that the grain structure of the nanocomposite composed of nanosize grains (<0.1 μm), ultrafine grains (0.1–1 μm) and micronsize grains (>1 μm) with random orientations. Mechanical properties of the material were examined at room and high temperatures by compression test. It was found that the yield strength of the UFG composite material is mainly controlled by the Orowan mechanism rather than the grain boundaries. The deformation... 

Nanostructured AA6063 (NS-Al) powder with an average grain size of ∼100 nm was synthesized by high-energy attrition milling of gas-atomized AA6063 powder followed by hot extrusion. The microstructural features of the consolidated specimen were studied by transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) techniques and compared with those of coarse-grained AA6063 (CG-Al) produced by hot powder extrusion of gas-atomized powder (without using mechanical milling). The consolidated NS-Al alloy consisted of elongated ultrafine grains (aspect ratio of ∼2.9) and equiaxed nanostructured grains. A high fraction (∼78%) of high-angle grain boundaries with average... 

Al6063 powder was subjected to severe plastic deformation via high-energy mechanical milling to prepare ultrafine-grained (UFG) aluminium alloy. Uniaxial compression test at various temperatures between 300 and 450 °C and strain rates between 0.01 and 1 s-1 was carried out to evaluate hot workability of the material. Microstructural studies were performed by EBSD and TEM. The average activation energy and strain rate sensitivity of the hot deformation process were determined to be 280 kJ mol-1 and 0.05, respectively. The deformation temperature and applied strain rate significantly affected the grain structure of UFG Al alloy. A finer grain structure was obtained at lower temperatures and... 

An experiment was conducted to determine whether allowing an aluminum melt to solidify in the crucible and later remelting it would improve the quality of the melt and the casting. To investigate this, data were collected through reduced pressure test, density measurement, metallography, X-ray radiography and tensile testing and analyzed statistically. Results indicated that remelting improved the quality of the melt by reduction of the number of defects in the casting and their area and volume fractions. The improvement in elongation of remelted specimens was found to be statistically significant. Analysis of deformation characteristics showed that the improvement in elongation is due to... 

Ultrafine-grained (UFG) Al6063 alloy reinforced with 0.8 vol% nanometric alumina particles (25 nm) was prepared by reactive mechanical alloying and direct powder extrusion. Transmission electron microscopy and electron backscatter diffraction analysis showed that the grain structure of the nanocomposite composed of nanosize grains (<0.1 μm), ultrafine grains (0.1-1 μm) and micronsize grains (>1 μm) with random orientations. Mechanical properties of the material were examined at room and high temperatures by compression test. It was found that the yield strength of the UFG composite material is mainly controlled by the Orowan mechanism rather than the grain boundaries. The deformation... 

The microstructure and mechanical properties of the ultra-fine grained (UFG) Al6063 alloy reinforced with nanometric aluminum oxide nanoparticles (25 nm) were investigated and compared with the coarse-grained (CG) Al6063 alloy (∼2 μm). The UFG materials were prepared by mechanical alloying (MA) under high-purity Ar and Ar-5 vol pct O2 atmospheres followed by hot powder extrusion (HPE). The CG alloy was produced by HPE of the gas-atomized Al6063 powder without applying MA. Electron backscatter diffraction under scanning electron microscopy together with transmission electron microscopy studies revealed that the microstructure of the milled powders after HPE consisted of ultra-fine grains... 

We studied the flow stress and microstructural changes of nanostructured Al-6063 alloy produced by mechanical alloying at various temperatures and strain rates. The analysis of flow curves was performed by a constitutive equation, and the stress exponent and activation energy were determined as functions of strain. The deformation mechanisms were elaborated through microstructural observations by electron backscattering diffraction and transmission electron microscopy. Coarsening of the subgrains and grain growth upon deformation was monitored and related to the Zener-Hollomon parameter  

Hot deformation behavior of Al6063 alloy produced by direct powder extrusion was studied by means of uniaxial compression test in the temperature range between 300 and 450°C and strain rate range between 0.01 and 1s -1. Electron backscatter diffraction (EBSD) technique and transmission electron microscopy (TEM) were utilized to study the microstructure of the material before and after the hot deformation. The microstructure of the extruded alloy consisted of elongated grains within a subgrain structure and small grains free of low angle grain boundaries (LAGBs). An equiaxed duplex microstructure consisting of large substructured grains and fine grains separated by high angle grain boundaries... 

A modified plastic yield function is proposed to predict the consolidation behavior of nanostructured metal powders and metal-matrix nanocomposite powders under uniaxial compaction. The validity of the model is verified for nanocrystalline Al6063 (~100nm) alloy reinforced without and with 0.8vol.% Al2O3 nanoparticles (~25nm). The plastic deformation propensity of these powders is analyzed by linear compaction equations. The yield stress of the powder compacts is shown to be influenced by the nano-scale grains and the reinforcement nanoparticles  

Nanostructured AA6063 (NS-Al) powder with an average grain size of ~100. nm was synthesized by high-energy attrition milling of gas-atomized AA6063 powder followed by hot extrusion. The microstructural features of the consolidated specimen were studied by transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) techniques and compared with those of coarse-grained AA6063 (CG-Al) produced by hot powder extrusion of gas-atomized powder (without using mechanical milling). The consolidated NS-Al alloy consisted of elongated ultrafine grains (aspect ratio of ~2.9) and equiaxed nanostructured grains. A high fraction (~78%) of high-angle grain boundaries with average... 

In this study, we are proposing a novel nonlinear classification approach to discriminate between Alzheimer's Disease (AD) and a control group using T1-weighted and T2-weighted Magnetic Resonance Images (MRI's) of brain. Since T1-weighted images and T2-weighted images have inherent physical differences, obviously each of them has its own particular medical data and hence, we extracted some specific features from each. Then the variations of the relevant eigenvalues of the extracted features were tracked to pick up the most informative ones. The final features were assigned to two parallel systems to be nonlinearly categorized. Considering the fact that AD defects the white and gray regions... 

In this work, nanocrystalline Al6063 composite powder reinforced with nanometric oxide ceramic particles was synthesized via an in situ solid-gas reaction during high-energy mechanical alloying under a mixture of argon-oxygen atmosphere. The effect of oxygen volume fraction on the morphological evolution and microstructural changes during mechanical alloying was studied by various analytical techniques including optical and electron microscopy, X-ray diffraction, laser particle size analysis, apparent density measurement, and microhardness test. The reactive mechanical alloying resulted in the formation of amorphous Al- and Al-Mg-Si-Fe oxides with a size range of 40-100. nm and volume... 

Ultrafine-grained (UFG) Al6063 matrix nanocomposites reinforced with nano-size Al2O3 were produced by reactive mechanical alloying and hot powder extrusion method. Microstructural studies were performed by transmission electron microscope (TEM) and electron backscatter diffraction (EBSD). Observation of very small regions with high- and low-angle grain misorientation, i.e. grains and subgrains, showed the formation of UFG Al alloy matrix with an average grain size of ~ 0.37 μm. A uniform distribution of alumina particles with an average size of ~ 100 nm was also achieved. Compression test at various temperatures up to 450 °C was carried out to evaluate the high-temperature strength and hot... 

NiTi alloys have exhibited significant potential as a matrix of wear resistant composites. In this study, in order to examine the effect of starting materials on the wear performance of NiTi-based composites, both elemental Ni/Ti and prealloyed NiTi powders were used to fabricate NiTi-6wt% nano-Al2O3 composites using hot isostatic pressing (HIP). Nanoindentation and microhardness test results indicate that the composite samples produced from the elemental Ni/Ti powders exhibited higher hardness and lower pseudoelasticity properties than those of the samples fabricated from the prealloyed NiTi powders; this is attributed to the higher amount of...