Sharif Digital Repository

Due to well mechanical properties and high resistance to environmental conditions, metal pipes are used to transport oil and gas products, water and sewage, as well as hydraulic systems in aircraft or aerospace systems. Therefore, maintenance of oil and gas transmission lines in energy-related industries and pressurized tanks in the aviation industry has always been a concern of engineers. Due to the problems of old methods for repairing damaged pipelines or aerial structures, it seems necessary to provide new, safe and cheap methods for repairing them. Various engineering standards for pipelines and their repairs have been presented so far which have analytical solutions to determine the... 

In 2009, a general equation of state (EOS-III) based on an effective near-neighbor pair interaction of an extended Lennard-Jones (3, 6, 12) type has been introduced as : , where is the compressibility factor, p and ρ stand for pressure and molar density , respectively, T is Temperature , and e, f and g are the temperature dependent coefficient of the equation of state . the Z_th and Z_in are the thermal and internal contributions of pressure in the compressibility factor, respectively. this equation of state gives a good description of all types of nano- and bulk –solid and bulk fluid at entire temperature and pressure ranges for which thee is experimental data. Investigation show that... 

In the present study, the thermal behavior of human teeth during laser radiation has been discussed. The high laser power, as well as its low emission, can allow deviations from the Fourier heat transfer model. To overcome this problem, the non- Fourier heat transfer method, dual phase lagged (DPL), has been used. Wisdom considered in this study to evaluate the thermal behavior of tooth. Using the finite volume method, the DPL equations are solved and the thermal response of the teeth is obtained during laser irradiation. The effect of delay times, which are the parameters of the DPL model and depart from the Fourier model, is fully demonstrated on the temperature behavior of the tooth, and... 

The rise in carbon dioxide levels has led to the manifestation of numerous environmental challenges. Currently, the absorption and conversion of carbon dioxide into valuable fuel resources such as synthetic gas, methane, and ethylene are deemed crucial from both environmental and economic standpoints. Despite the presentation of photocatalysts such as titanium oxide and electrocatalysts such as copper, silver, and zinc, their efficiency in CO2 conversion is found to be insufficient. One potential solution to this problem is the utilization of photoelectrocatalytic CO2 recovery. In this study, the aim was to enhance the photoelectrocatalytic reduction of CO2 by designing and manufacturing... 

Preformed particle gels (PPGs) due to its advatantage over commonly used in situ gels has been successfully applied for controlling excess water production in mature oil reservoirs. Field results of using PPGs in oil fields shows that commonly used PPGs are highly sensitive to hard reservoir conditions such as high temperature and salinity and can not effectively block fractures and high permeability layers.Objects of this study are synthesis and evaluating performance of this novel polymer based hydrogel in oil reservoirs with high temperature and salinity. Central composite design ( which is a experiment design approach) was used for synthesizing thirteen gel samples and optimal sample was... 

Biological layers are one of the main problems related to water transfer with pipe lines which are formed through time in the inner surface of the pipes by the water nutrients. Hence, the inner surfaces in the pipe lines and water refineries should be made in order not to let these biological layers to be made. The reason is that when the biofilm is formed on these surfaces, the traversing water is polluted. Dredging of these pipes is not only necessary in most of the countries in the world and needs huge amounts of water but is also very complex and expensive.In this research, nanomaterials, namely ZnO, T〖iO〗_2،S〖iO〗_2 have been used to cover the surface of concrete and steel pipes (The... 

Sand production from oil reservoirs leads to various problems, such as well productivity reduction, operating equipment corrosion, and increased production costs. Therefore, controlling sand production in unconsolidated reservoirs is crucial for operating companies. Chemical injection into the formation in order to strengthen and reduce sand production is one of the most important methods of sand control. In this study, a hydrogel nanocomposite was designed and its effectiveness in sand control was investigated. Various tests were carried out to define and assess its efficacy, as follows: Morphological tests demonstrated the creation of a dense, homogeneous, and porous structure. Structural... 

The present thesis investigates the surge phenomenon of high speed centrifugal compressors. Surge is a highly undesired condition and may cause severe damage to the machine and thus the plant. Traditionally, surge is avoided via a surge avoidance scheme wih recycle valve in discharge at the most common approach. A one dimensional technique is developed where the Greitzer lumped parameter model along with the Gravdahl one dimensional model is considered as the basis. Shaft dynamics, volume dynamics, losses, energy transfer and time lag are imbedded in the present model to improve the prediction of the compressor characteristics beyond the stability region. On the other hand, in order to... 

Axial compressor design is a very complex and expensive process. In general, for design and development of a new axial compressor, manufacturing companies usually intend to employ an existing and successful axial compressor as an starting point and modify and upgrade it. In this regard, dimensional scaling is a common method for derivative axial compressors. The goal of dimensional scaling is to get a different capacitywhile minimizing the development time and cost. In this thesis, theNASA eight stage transonic axial flow compressor is chosen as the base model for dimensional scaling to lower and upper size of its original dimension. The scaled compressor is analyzed with a quasi 2-D code.... 

The purpose of this research is theoretical and numerical investigations on centrifugal compressor. A computer code has been developed to simulate single-zone and two-zone model, based on the revised formulation for real gas, using Peng-Robinson equations. Single-zone modeling, also known as meanline method, established based on 1-D equations of fluid dynamics considering ideal gas relations, empirical loss correlations, slip factors, impeller efficiency and no wake or separation regions. Considering usual significant separated regions in the gas path of impellers, two-zone (jet and wake zone) model has been developed to achieve a more reliable simulation by using fewer correlations based on... 

In this research, the principles of design of Heat Exchangers in thermoacoustic systems are developed. The Heat Exchangers as a essential part of thermoacoustic systems, complete the thermodynamic cycle in these systems. In this thesis, principles and algorithms of design for Shell&Tube, Plate and Screen Heat Exchangers are described and these principles are validated for each kind of Heat Exchangers. Then the balance of exergy is studied in thermoacoustic systems and at the end, for every Heat Exchangers amount of exergy destruction is evaluated for oscillating and non-oscillating fluids. Based on fitness functions of exergy destruction, heat transfer area and acoustic pressure drop, Heat... 

Compression systems are widely used in industry. Dynamic Modeling is a necessary step in design procedure of a safe compression system. A dynamic model should be adequate and simulate dominant elements of system. One important element of industrial compression systems is downstream pipelines. In this work, a dynamic model including pipeline acoustics is developed. It is accepted that changes of working gas molecular weight can cause inception of instabilities in compression systems. The dynamic model used to study mechanisms of these instabilities. A conventional control system is modeled and tuned for the compression system. The ability of this control system to prevent such instabilities... 

thermoacuostic heat pump (THP) is One of the most important thermoacuostic applications which is used for heat lost recovery in industrial applications and civil applications.In this project, we have a quick review on thermoacuostic theory and researches in this field. Also a thermoacuostic heat pump in a lab scale will be designed and analyzed.For achieving this goal, first, mathematical equations of thermoacuostic systems are reviewed; a thermoacuostic heat pump is designed on the base of Tijani method and final model is validated by DeltaEC software. In the next step, after investigating about laboratory equipments which is used in testing process, we generate test matrix and study about... 

Typical thermoacoustic systems deal with the conversion of heat energy to sound energy and vice versa. Recent advances in the field of thermoacoustics have altered the working mechanism of many conventional heating and cooling devices. These systems have three highlighted advantages: first, they have simple structure, no moving parts, low cost of manufacture, and high reliability; second, by using inert gases as working fluid, they are environmentally friendly; and finally, heat driven thermoacoustic devices can be driven by low quality energy sources such as waste heat and solar energy.
The main focus of the present thesis is on the application of the thermoacoustic technology in the...