Sharif Digital Repository

The ceramic fracture in output RF window is one of the most important failure factors in high power microwave sources. Fast protection systems are used to protect the source. The methods for determining the required protection response time are conservative and rough. In this paper, an investigation is presented about the twin growth in the ceramic of RF window in faulty condition. It is shown that the twin growth in ceramic can be a reliable figure of merit for the response time calculation of the microwave source protection system  

Alumina is widely used as a vacuum ceramic separator in the pillbox-type output window of high-power electron tubes. The fracture of alumina is one of the most important factors in the failure of these tubes. In this article, the fracture process of alumina in the pillbox-type window of high-power electron tubes is assessed microscopically. The investigation shows the twinning phenomenon in the fractured alumina. The reason for initiating and propagating twins is also investigated. An increase in the alumina temperature decreases the required stress level for generating twins. The overheating condition occurs due to an impedance mismatch in the pillbox-type window. Experimental and numerical... 

In this paper, the effect of voltage ripple of the cathode power supply on the phase noise of high power electron tubes is experimentally studied. The conducted experiments are carried out on a traveling wave tube. A high voltage cathode power supply with voltage ripple adjusting capability is used to apply the various levels of voltage ripple to the studied tube. The designed power supply is able to provide a wide range of voltage ripple from the high values to very low values. Therefore, it is possible to study the behaviour of the tube at the cathode voltage with a very low ripple. The output power spectrum of the tube is presented to show the level of the tube phase noise. The... 

Single-walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWCNTs) were synthesized in aqueous solutions containing FeCl2, FeCl3, FeSO4 and Fe2(SO4)3. The effects of iron charge and the counter ions on the formation of carbon nanotubes (CNTs) were investigated. Thermogravimetric (TG) analysis indicated that carbon multilayer structures including CNTs and multishell graphite particles were formed in deionized (DI) water without the iron precursor. SWCNTs were also synthesized in the presence of the iron ions. It was also found that the mole ratio of [Fe2+]/[Fe3+] in the solution has a significant influence on the purity of CNTs and the process yield. The highest yield was... 

Nowadays there are more than thirty maturity models in different knowledge areas. Maturity model is an area of interest that contributes organizations to find out where they are in a specific knowledge area and how to improve it. As Information Resource Management (IRM) is the concept that information is a major corporate resource and must be managed using the same basic principles used to manage other assets, assessment of the current IRM status and reveal the improvement points can play a critical role in developing an appropriate information structure in organizations. In this paper we proposed a framework for information resource management maturity model (IRM3) that includes ten best... 

This paper presents a new mechanism with unique and prominent features for a helical swimmer robot. "Double Helices Propulsion Mechanism" consists of two parallel helices with a single axis rotating in the same direction. The outer helix acts as the main propulsion component, and the inner helix, which is made of a Shape Memory Alloy (SMA), controls the forward velocity during swimming. This mechanism, by varying the geometrical parameters of its helical tail, can change the forward velocity of the helical swimmer robot that is required by its predefined missions. In order to study the effects of geometric parameters on the forward velocity in the single helical swimmer, a hydrodynamic model... 

Data Envelopment Analysis (DEA) is a method to measure the efficiency of a DMU (Decision Making Unit, e.g. school, public agencies and banks). One of the ways for determining rank of DMUs is efficient score of each DMU. An interesting research issues is to discriminate between efficient DMUs. In literatures, supper efficiency is an applicable method for ranking efficient DMUs. The main drawback of this method is an inability of this method to rank non-extreme efficient DMUs. Therefore, this issue reduces the usefulness of this method. In this paper we propose a new ranking system for non-extreme efficient DMUs (Decision Making Units) based upon the omission of DMUs from reference set of the... 

The purpose of this paper is to present a polynomial time algorithm which determines the lot sizes for purchase component in Material Requirement Planning (MRP) environments with deterministic time-phased demand with zero lead time. In this model, backlog is not permitted, the unit purchasing price is based on the all-units discount system and resale of the excess units is possible at the ordering time. The properties of an optimal order policy are argued and on the basis of them, a branch and bound algorithm is presented to construct an optimal sequence of order policies. In the proposed B&B algorithm, some useful fathoming rules have been proven to make the algorithm very efficient. By... 

Cooling water is used to remove the heat from stator bar of large turbogenerators and prevent additional temperature rise. Blockage of these channels leads to heat traps along the stator bar and its temperature failure. In addition, transposition of strands in a bar causes accumulation of heat in some parts of stator bar because of non-uniform arrangement of cooling channels especially when some of channels are blocked. In this paper, effect of cooling water channels blockage is studied using a precise thermal model. It is shown that such heat traps cause additional temperature rise in stator bars and this phenomenon can not be detected by thermal sensors of turbogenerator. Laboratory and... 

This paper investigates the multiple output full bridge based DC-DC converter and derives the analytical expression for its cross regulation. The effect of input voltage is studied and a topology is proposed that boosts the input voltage by a single stage structure. The proposed converter is based on Z-Source Inverter. In addition, the modulation scheme of the converter is presented. Simulation and experimental results are presented to verify the analytical study  

Electron guns are used as the electron sources in high-power electron tubes. The generated electron beam in electric guns passes through an aperture at the center of the anode. Since the electron beam has considerable kinetic energy, any collision between the electron beam and the anode aperture edge damages the electron gun. Therefore, electron guns are designed to meet the compatibility between the diameters of the electron beam and the anode aperture. However, this compatibility is disrupted during the transient time interval of the gun's power supply. In this article, the cause of failure of the electron gun of high-power electron tubes is investigated for the transient interval of the...