Sharif Digital Repository

In this article, the synthesis of magnetite nanostructures was successfully carried out by the sonochemical process. In this method, stoichiometric amount of iron chlorides (FeCl3.6H2O and FeCl2.4H2O), ammonia (NH3) and polyvinylpyrolidone (PVP) were used to synthesize pure Fe3O4 nanoparticles. The effect of initial sonication power of the ultrasonic device on the size and morphology of the final products as one of the effective parameters was investigated. For this, the initial power of the sonicator was evaluated at 90, 70, 50 and 30 W at 40°C. Characterization of Fe3O4 nanoparticles was done by transmission electron microscope (TEM) and X-ray powder diffraction (XRD) and its magnetic... 

Surface modification of titanium implants is recently considered by several researchers. In this study, PEO was performed over commercially Ti-6Al-4V alloy pellets in an aqueous electrolyte containing calcium acetate (C.A.) and calcium glycerphosphate (Ca-GP) with a Ca/P molar ratio of 6.8, and applying current density of 0.212 A/cm2, frequency of 100 Hz and duty ratio of 60% for 4 min. In the next step, hydrothermal treatments were carried out for various durations and at different temperatures inside an autoclave chamber containing a NaOH solution with pH of 11.5. XRD and SEM results confirmed formation of needle-shaped HAp after all hydrothermal conditions. Maximum intensity of HAp peaks... 

This work presents an innovative design for a flow-through dielectrophoretic cell sorting based on silicon bulk microelectrodes featuring sidewall undercuts. The microelectrodes are configured into an interdigitated array with digits extending across the flow chamber at an oblique angle against the flow stream. Target cells under dielectrophoretic forces and hydrodynamic drag can slide along the digits to a dedicated outlet. The design has been showcased for continuous-flow sorting of viable and non-viable mammalian cells, achieving a throughput of 16,600 cells/min, an order of magnitude higher than those reported for existing continuous-flow cell sorting designs using thin-film or... 

In this paper, we have proposed, designed, implemented, and characterized a low-cost camera-based microarray scanner which is capable of imaging fluorescently-labeled DNA or Protein microarrays. The proposed system is designed to simultaneously measure two different fluorescent dyes using two parallel channels which increase the overall scan speed. We have shown that the wide dynamic range of system makes it able to detect fluorophore densities from 100-106 molecule/μm2. In each capture, a 5.6 mm × 3.7 mm field is imaged on a 22.3 mm × 14.9 mm (18 megapixels) CMOS sensor. Therefore, the microarray can be scanned with ∼ 1μm2 spatial resolution which is high enough to distinguish borders of... 

In this study the investigation of large deflections subject in compliant mechanisms is presented using homotopy perturbation method (HPM). The main purpose is to propose a convenient method of solution for the large deflection problem in compliant mechanisms in order to overcome the difficulty and complexity of conventional methods, as well as for the purpose of mathematical modeling and optimization. For simplicity, a cantilever beam of linear elastic material under horizontal, vertical and bending moment end point load is considered. The results show that the applied method is very accurate and capable for cantilever beams and can be used for a large category of practical problems for the... 

With the rise in oil price and population growth, renewable energies are assumed to be the main source of energies for the next generation. Wind as a natural, eco-friendly and renewable source of energy has been at the center of concentration for decades. Recently there has been some ideas regarding the self-regulating urban wind turbines. Researchers have shown that a proper enclosure increases the wind velocity and therefore more torques can be exerted on the rotors, therefore more power can be generated. These enclosures are light and cheap, therefore they are applicable and effective. In the present study, an enclosure was modified to increase the exerted torque with implementing a step... 

We have studied the relation between the spark-gap operation parameters and the plasma pinch and Neutron yield in our Filippov-type plasma focus, Dena, with 90kJ energy storage bank (25kV, 0.288mF). It has been found that better pinches with regard to their Neutron yield, generally are associated with a faster breakdown in the trigger-able spark-gap as well as higher current buildup rate. We have measured the current buildup speed at various operating conditions and derived the experimental primary ionization parameter and drift velocity of electrons, at extremely high field to pressure ratios. Also, an elaborate axisymmetric variational time-domain finite element simulation code has been... 

Conventional propellers might undergo severe cavitation at high speeds and this phenomenon not only affects the efficiency of the propeller, but also may result in serious damages in propulsion system. Due to their special geometries, surface piercing propellers (SPPs) overcome this problem and achieve high efficiencies in high speeds. Therefore, SPPs are one of the popular propulsors for high-speed crafts. The present research is aimed to pursue SPP's performance in the off-design conditions. URANS method was used to study the performance of the 841-SPP (case with some available experimental results; Olofsson, 1996) in several immersion ratios (= 33%, 50%, 75% and 100%) and maneuvering... 

Here we report a versatile new method for endfunctionalizing polystyrene. In order to produce polystyrene with an amino end group, 2-(3-bromo-3- phenylpropyl) isoindoline-1,3-dione was synthesized and used as a novel initiator for ATRP. After ATRP polymerization, tri-n-butyltin hydride ((n-Bu) 3SnH) reductively replace existing halogens on polymer chains by hydrogen. Finally, the phthaloyl groups on polymer backbone were cleaved by treatment with hydrazine yielding amino terminated polystyrene. A polymer with M n≈10,350 and M w/M n01.17 was obtained. Therefore, this method allows the preparation of amino end functionalized polystyrene of narrow polydispersity with complete degree of... 

How does the brain process natural visual stimuli to make a decision? Imagine driving through fog. An object looms ahead. What do you do? This decision requires not only identifying the object but also choosing an action based on your decision confidence. In this circumstance, confidence is making a bridge between seeing and believing. Our study unveils how the brain processes visual information to make such decisions with an assessment of confidence, using a model inspired by the visual cortex. To computationally model the process, this study uses a spiking neural network inspired by the hierarchy of the visual cortex in mammals to investigate the dynamics of feedforward object recognition... 

In this paper, a new method is proposed for modal parameter estimation using time-frequency representations. Smoothed Pseudo Wigner-Ville distribution which is a member of the Cohen's class distributions is used to decouple vibration modes completely in order to study each mode separately. This distribution reduces cross-terms which are troublesome in Wigner-Ville distribution and retains the resolution as well. The method was applied to highly damped systems, and results were superior to those obtained via other conventional methods. © 2006 Elsevier Ltd. All rights reserved  

In this paper, a new method for modal parameter estimation using time-frequency representations is presented. Smoothed Pseudo Wigner-Ville representation which is a member of the Cohen's class distributions is used that reduces cross-terms in time-frequency plane dramatically and holds resolution as well. The method was applied to systems with high damping, and the results were superior to other conventional methods. © (2006) by the Katholieke Universiteit Leuven Department of Mechanical Engineering All rights reserved