Sharif Digital Repository

Focused on the assessment of the diphenhydramine hydrochloride (DPH) capabilities as an alternative to conventional and harmful industrial corrosion inhibitors, electrochemical techniques were employed. The optimum concentration of 1000 ppm was determined by molecular simulation and validated through electrochemical experiments. The results acquired from the electrochemical impedance spectroscopy (EIS) study showed that DPH at a concentration of 1000 ppm has a corrosion efficiency of 91.43% after 6 h immersion. The DPH molecules' orientation on the surface was assessed based on EIS predicting horizontal adsorption on the surface. Molecular simulations were done to explore the adsorption... 

The stability of unsaturated slopes under seismic loading has become an important issue over the past few years which is the indication of its practical significance in geoengineering. This study aims at exploring the seismic stability of unsaturated sandy clay and silty clayey sand slopes using 2D limit equilibrium analysis for different slope geometries and ground water levels. To this end, the pseudo-static and the displacement-based sliding block Newmark’s approaches are employed for parametric studies by considering the records of the 2003 earthquake that devastated the city of Bam, in the southeast of Iran. In all analyses, the unsaturated state of the soil materials is taken into... 

Previous studies have not extensively explored the collective impact of lateral, axial, and thermal loading on the ultimate vertical bearing capacity of energy piles, qu. This study investigates qu values for energy piles in dry sandy and clayey soils under varying lateral loads and temperature conditions using numerical and analytical solutions, considering temperature-dependent variables. The numerical results were validated against experimental data. The analytical solution aligns well with numerical analyses, though it yields slightly higher qu values in sandy soil. Both numerical and analytical solutions show that cooling and heating can respectively increase and decrease qu under... 

In this paper effects of material properties estimations, used for particulate reinforced composites, on the thermo-mechanical response of functionally graded sphere and cylinder are presented. A numerical solution for an arbitrary material gradation is obtained for each geometry independently. With this assumption, the governing partial differential equations are reduced to an ordinary differential equation in each geometry. The thermo-elastic solution for hollow sphere is derived using spherical symmetry. However, plane strain and axial symmetry are assumed for solving hollow cylinder. In the numerical method, radial domain is divided into some finite sub-domains and material properties... 

Blotches are the common artifacts in degraded motion picture sequences. They are usually caused by placing dust and dirt on film surfaces as well as abrasion of film materials. Blotches are seen as dark and bright flashes spreading through the frames, randomly. The spike detection index (SDIa) method is the simplest approach used to detect these artifacts. However, when the motion vectors are not precise enough in some points they might be declared as blotches too. This situation can also occur in areas containing a high level of noise. To overcome these difficulties, two post-processing methods are proposed in this paper. In the first method, the edge points are first omitted from the set... 

Situational awareness (SA) and fatigue management are crucial aspects of aviation safety, particularly during demanding flight phases. This study introduces an innovative approach employing flight data, machine learning, and Continuous Performance Test (CPT) metrics to predict pilot performance and SA during instrument approaches under Instrument Meteorological Conditions (IMC). Data were collected from over 10 pilots across more than 40 flights in a high-fidelity Cessna 172 analog flight simulator. Significant correlations were observed between dynamic cognitive performance parameters and the exceedance shape factor, a novel measure of pilot sustained attention introduced in this research.... 

A fully-automated unsaturated triaxial device is developed at the Advanced Soil Mechanic Laboratory of the Sharif University of Technology (SUT) to investigate the hydromechanical behavior of unsaturated soils under any complicated path. The main improvements of the developed device are (1) the ability to continuously measure accurately different stress/strain variables during long duration of unsaturated tests. This is of great importance in capturing the sudden deformations of the specimen, under wetting (2) providing a user-friendly controller software enabling the definition of any desired stress/strain variable and stress/strain paths under either stress-controlled or strain-controlled... 

The evaluation of multigroup constants in reactor calculations depends on several parameters. One of these parameters is the Dancoff factor which is used for calculating the resonance integral and flux depression in the resonance region in heterogeneous systems. In the current paper, a computer program (MCDAN-3D) is developed for calculating three dimensional black and gray Dancoff coefficients, based on Monte Carlo, escape probability and neutron free flight methods. The developed program is capable to calculate the Dancoff factor for an arbitrary arrangement of fuel and moderator pebbles. Moreover this program can simulate fuels with homogeneous and heterogeneous compositions. It might... 

Evaluation of multigroup constants in reactor calculations depends on several parameters, the Dancoff factor amid them is used for calculation of the resonance integral as well as flux depression in the resonance region in the heterogeneous systems. This paper focuses on the computer program (MCDAN-3D) developed for calculation of the multigroup black and gray Dancoff factor in three dimensional geometry based on Monte Carlo and escape probability methods. The developed program is capable to calculate the Dancoff factor for an arbitrary arrangement of fuel rods with different cylindrical fuel dimensions and control rods with various lengths inserted in the reactor core. The initiative... 

Shear yielding (SY) and shear rupture (SR) are base metal failure modes in welded connections of brace members to gusset plates. Although gusset plated connections have been extensively investigated in the past nonetheless, the shear failure limit states of welded brace members have not received significant attention. This paper aims to shed some light on the shear failure mechanism and strength of welded brace members consisting of single and double channels and angles. For this purpose, a nonlinear finite element (FE) model with ductile damage simulation is developed and validated against the authors’ experiments and other available test results. Then an extensive parametric study using...