Loading...
Search for: dehabadi--m
0.138 seconds

    Reliability modeling of anomaly detection algorithms for wireless body area networks

    , Article 2017 25th Iranian Conference on Electrical Engineering, ICEE 2017, 2 May 2017 through 4 May 2017 ; 2017 , Pages 70-75 ; 9781509059638 (ISBN) Zare Dehabadi, M. S ; Jahed, M ; Sharif University of Technology
    2017
    Abstract
    Research on Wireless Body Area Networks (WBAN) has witnessed constant advances in small and low power integrated electronic circuits as well as wireless communication schemes for remote monitoring of patients. As such, high reliability anomaly detection has emerged as an important characteristic especially in detection of system faults and abnormal physiological measurements. This work studies the reliability of WBANs by utilizing a Markov-based chain model and considering hardware failure rate, patient health status, and accuracy of anomaly detection algorithms containing Detection Rate (DR), False Positive Rate (FPR), and accuracy of transient fault correction measures. The proposed... 

    Compensation for electrical fatigue in piezoelectric transducers

    , Article IEEE Transactions on Instrumentation and Measurement ; Volume 72 , 2023 ; 00189456 (ISSN) Zare Dehabadi, M. S ; Jahed, M ; Sharif University of Technology
    Institute of Electrical and Electronics Engineers Inc  2023
    Abstract
    Malfunction of ultrasonic transducers is one of the most common factors affecting the quality of medical ultrasound images. In this work, the effect of electrical fatigue in piezoelectric transducers on the image quality is investigated and subsequently compensated. To this end, through a combination of simulation and controlled experimental and clinical evaluations, the effect of fatigue and its compensation is realized. Initially, the electrical fatigue is simulated by reducing the piezoelectric permittivity and piezoelectric constant parameters based on finite element method (FEM). Next, the transducer's electromechanical impulse response is obtained, and the quality of reconstructed... 

    Medical ultrasound image restoration in presence of defective transducer elements

    , Article 2023 31st International Conference on Electrical Engineering, ICEE 2023 ; 2023 , Pages 271-277 ; 979-835031256-0 (ISBN) Zare Dehabadi, M. S ; Jahed, M ; Sharif University of Technology
    Institute of Electrical and Electronics Engineers Inc  2023
    Abstract
    Quality of medical ultrasound images is negatively affected by common defective elements in the ultrasonic transducer arrays. In this work, radio frequency (RF) signals from weak elements with low sensitivity are restored using an adaptive nonblind signal deconvolution method. For this purpose, the electromechanical impulse response of each element in the transducer must be measured. Initially, the negative effects of the RF signals recorded from each element are removed by Wiener deconvolution of RF signals through the measured impulse responses. Then to restore the RF signals, the deconvolution result is convolved with the reference electromechanical impulse response, corresponding to the... 

    Using commercial calcium ionophores to make lanthanide sensors

    , Article Journal of Radioanalytical and Nuclear Chemistry ; Volume 331, Issue 4 , 2022 , Pages 1751-1758 ; 02365731 (ISSN) Dehabadi, M ; Saveliev, M ; Legin, A ; Yaghmaei, S ; Babain, V ; Kirsanov, D ; Sharif University of Technology
    Springer Science and Business Media B.V  2022
    Abstract
    Developing chemical sensors with pronounced sensitivity towards lanthanides is a very important task related to the analytical control of industrial processes in nuclear industry. Various diamides of organic acids were shown to be very effective for such sensing applications when employed as ligands in plasticized polymeric membranes of potentiometric sensors. The chemical structures of some of these ligands (diamides of diglycolic acid) are very similar to those suggested in 80’s as Ca(II) ionophores that were later commercialized. We have hypothesized that commercial ionophores ETH 129 (N,N,N′,N′-tetra[cyclohexyl] diglycolic acid diamide) and ETH 5234... 

    Identification of β-lactam-resistant coding genes in the treatment plant bactivated sludge process

    , Article Desalination and Water Treatment ; Volume 281 , 2023 , Pages 137-149 ; 19443994 (ISSN) Moradi, S ; Fouladi Fard, R ; Aali, R ; Dolati, M ; Shams, S ; Asadi Ghalhari, M ; Hamta, A ; Dehabadi, M ; Sharif University of Technology
    Desalination Publications  2023
    Abstract
    Wastewater treatment plants are the most important release source of antibiotic-resistance genes (ARGs) into the environment. This study aimed to identify β-lactam-resistance genes in Qom prov-ince municipal wastewater and also to determine the effect of municipal wastewater treatment plants with different processes on reducing these pollutants. Sampling was performed according to the standard protocol and at constant temperature conditions. Nine genes resistant to the six groups of β-lactam antibiotics were selected, and polymerase chain reaction (PCR) test was performed to identify the presence/absence of ARGs. At the same time, real-time PCR test was also carried out to quantitatively... 

    Introducing a Supervisory Hardware Platform for Wireless Body Area Sensor Network with an Anomaly Detection Ability

    , M.Sc. Thesis Sharif University of Technology Zare Dehabadi, Mohammad Saeed (Author) ; Jahed, Mehran (Supervisor)
    Abstract
    Wireless Body Area Network (WBAN) is a set of various physiological sensors for remote monitoring and controlling of the patient’s health status. Detection of anomalies, containing faults and physiological stresses, and distinguishing between them can eliminate the need for constant presence of specialists and decrease the occurrence of False Alarm Rate (FAR).A supervisory hardware platform for WBAN architecture is introduced and implemented in this thesis. The proposed architecture contains three sensors for recording of biomedical signals, heart rate, SpO2 and body temperature simultaneously and transmitting them to central node wirelessly through Wi-Fi standard. This proposed architecture... 

    Vibration effect on electrical resistance fluctuations in electrical connectors

    , Article Engineering Solid Mechanics ; Volume 6, Issue 4 , 2018 , Pages 299-306 ; 22918744 (ISSN) Behzad, M ; Darvish Gohari, H ; Mohammadi Dehabadi, A. A ; Sharif University of Technology
    Growing Science  2018
    Abstract
    Proper functioning of electrical connectors used in high oscillation is of great importance. Vibrations in connector pins cause stress and electrical resistance variations in the contact surface. In the present paper, the impacts of vibrational loads on electrical connectors is being modeled using the finite element method, and the electrical resistance oscillations of the connectors will be examined. Ultimately, the parameters affecting the electrical resistance oscillations of contacts will be determined and their relations with oscillations in electrical resistance are specified as well. © 2018 by the authors; licensee Growing Science, Canada, 2018 Growing Science Ltd. All rights reserved... 

    Novel pillar[5]arenes show high cross-sensitivity in pvc-plasticized membrane potentiometric sensors

    , Article Chemosensors ; Volume 10, Issue 10 , 2022 ; 22279040 (ISSN) Dehabadi, M ; Yemisci, E ; Kursunlu, A. N ; Kirsanov, D ; Sharif University of Technology
    MDPI  2022
    Abstract
    In this study a variety of novel symmetrically and asymmetrically functionalized pillar[5]arenes were synthesized, structurally characterized and applied as ionophores in PVC-plasticized membrane potentiometric sensors. During the sensitivity studies it was found that these novel sensors demonstrate pronounced cationic response towards different metal ions in aqueous solutions. A selectivity evaluation revealed that the developed sensors do not possess sharp preferences to particular ions, but offer a broad cross-sensitivity and can be employed in potentiometric multisensor systems. © 2022 by the authors  

    Robust Reconstruction of Medical Ultrasound Images in The Presence of Transducer Faults

    , Ph.D. Dissertation Sharif University of Technology Zare Dehabadi, Mohammad Saeed (Author) ; Jahed, Mehran (Supervisor)
    Abstract
    Medical ultrasound imaging is one of the common imaging methods in modern medicine, which is used to diagnose and even treat some diseases due to its cheapness and harmlessness. Medical ultrasound transducer arrays have a significant error rate. They are a major cause of failure in ultrasound imaging systems. This problem causes a noticeable decrease in the quality of the images and medical misdiagnoses. The topics of accurate detection of the location and severity of the error or failure, as well as the compensation for weak transducers by signal processing methods, have received less attention from predecessor researchers. In this thesis, an innovative method for accurate error detection... 

    Experimental Studies on Photocatalytic Removal of Dye Using Titanium Dioxide and Zinc Oxide Nanoparticles

    , M.Sc. Thesis Sharif University of Technology Dehabadi, Monireh (Author) ; Kariminia, Hamid Reza (Supervisor) ; Vossoughi, Manoochehr (Supervisor)
    Abstract
    Textile industry wastewaters are one of the important sources of environmental contamination because they produce large quantities of highly colored effluents. In recent years, use of advanced oxidation processes by producing highly active and reactive components such as hydroxyl radicals has been proposed. In this study, two oxygenated photocatalytic systems including UV/ZnO and UV/TiO2 were examined for degradation of C.I. reactive orange 16 dye as a typical organic pollutant in textile effluents. A thin gap annular photoreactor was designed and applied for the experiments. The photoreactor provided large surface area exposed to UV light, where in the solution layer renewal on the UV... 

    Developing potentiometric sensors for scandium

    , Article Sensors and Actuators B: Chemical ; Volume 348 , 2021 ; 09254005 (ISSN) Dehabadi, M ; Legin, E ; Legin, A ; Yaghmaei, S ; Nechaev, A ; Babain, V ; Kirsanov, D ; Sharif University of Technology
    Elsevier B.V  2021
    Abstract
    Scandium is a rare earth element that is not very abundant on Earth, however in recent years due to the employment of scandium in various high-tech fields the interest in the analytical chemistry of this metal is growing. Currently, the methods for scandium quantification are mainly based on inductively coupled plasma atomic emission and mass-spectrometry and to the best of our knowledge no potentiometric sensors for scandium detection were reported so far. This study is devoted to the development of simple and cost-effective ion-selective sensors for quantification of Sc3+ in aqueous media. Employing the variety of lipophilic ligands suggested in liquid extraction for separation of... 

    Development of Miniaturized Electrochemical Sensors Based on Ion-Selective Membrane for Environmental Applications

    , Ph.D. Dissertation Sharif University of Technology Dehabadi, Monireh (Author) ; Yaghmaei, Soheila (Supervisor) ; Legin, Andrey (Supervisor) ; Kirsanov, Dmitry (Supervisor) ; Babain, Vasiliy (Supervisor)
    Abstract
    The first study of the present research aims to the possibility of developing simple, accurate and selective potentiometric sensors for the detection of scandium ions in aqueous solution, which is done for the first time. In this study, a sensor array consisting of 17 miniaturized potentiometric sensors based on polymeric membranes containing various ion-extracting ligands were designed and fabricated. Ligands as the active component of the membranes included phosphine oxides and diamides of various organic acids, which were used in the extraction of rare earth metal ions. The possibility of using these extractants in the polymer matrix of membranes for the development of scandium-sensitive... 

    Probability of missed detection as a criterion for receiver placement in MIMO PCL

    , Article IEEE National Radar Conference - Proceedings, 7 May 2012 through 11 May 2012, Atlanta, GA ; 2012 , Pages 0924-0927 ; 10975659 (ISSN) ; 9781467306584 (ISBN) Majd, M. N ; Chitgarha, M. M ; Radmard, M ; Nayebi, M. M ; Sharif University of Technology
    IEEE  2012
    Abstract
    Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

    An efficient method for the ring opening of epoxides with aromatic amines by Sb(III) chloride under microwave irradiation

    , Article Journal of Chemical Research ; Issue 4 , 2008 , Pages 220-221 ; 03082342 (ISSN) Ghazanfari, D ; Hashemi, M. M ; Mottaghi, M. M ; Foroughi, M. M ; Sharif University of Technology
    2008
    Abstract
    SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

    Resource allocation for uav-enabled integrated sensing and communication (isac) via multi-objective optimization

    , Article ICASSP, IEEE International Conference on Acoustics, Speech and Signal Processing - Proceedings ; Volume 2023-June , 2023 ; 15206149 (ISSN); 978-172816327-7 (ISBN) Rezaei, O ; Naghsh, M. M ; Karbasi, M ; Nayebi, M. M ; Sharif University of Technology
    Institute of Electrical and Electronics Engineers Inc  2023
    Abstract
    In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

    MIMO radar signal design to improve the MIMO ambiguity function via maximizing its peak

    , Article Signal Processing ; Volume 118 , 2016 , Pages 139-152 ; 01651684 (ISSN) Chitgarha, M. M ; Radmard, M ; Nazari Majd, M ; Karbasi, S. M ; Nayebi, M. M ; Sharif University of Technology
    Elsevier  2016
    Abstract
    One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

    Detection-localization tradeoff in MIMO radars

    , Article Radioengineering ; Volume 26, Issue 2 , 2017 , Pages 581-587 ; 12102512 (ISSN) Nazari Majd, M ; Radmard, M ; Chitgarha, M. M ; Bastani, M. H ; Nayebi, M. M ; Sharif University of Technology
    2017
    Abstract
    Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

    Antenna placement and power allocation optimization in MIMO detection

    , Article IEEE Transactions on Aerospace and Electronic Systems ; Vol. 50, Issue 2 , April , 2014 , pp. 1468-1478 Radmard, M ; Chitgarha, M. M ; Majd, M. N ; Nayebi, M. M ; Sharif University of Technology
    2014
    Abstract
    It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

    Ambiguity function of MIMO radar with widely separated antennas

    , Article Proceedings International Radar Symposium ; 16 -18 June , 2014 ; ISSN: 21555753 Radmard, M ; Chitgarha, M. M ; Nazari Majd, M ; Nayebi, M. M ; Sharif University of Technology
    2014
    Abstract
    There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

    Choosing the position of the receiver in a MISO passive radar system

    , Article European Microwave Week 2012: "Space for Microwaves", EuMW 2012, Conference Proceedings - 9th European Radar Conference, EuRAD 2012 ; 2012 , Pages 318-321 ; 9782874870293 (ISBN) Chitgarha, M. M ; Majd, M. N ; Radmard, M ; Nayebi, M. M ; Sharif University of Technology
    2012
    Abstract
    By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only...