Loading...
Search for:
chahardori--m
0.134 seconds
Total 21473 records
A sub 1 v high PSRR CMOS bandgap voltage reference
, Article Microelectronics Journal ; Volume 42, Issue 9 , 2011 , Pages 1057-1065 ; 00262692 (ISSN) ; Atarodi, M ; Sharifkhani, M ; Sharif University of Technology
2011
Abstract
A Bandgap circuit capable of generating a reference voltage of less than 1 V with high PSRR and low temperature sensitivity is proposed. High PSRR achieved by means of an improved current mode regulator which isolates the bandgap voltage from the variations and the noise of the power supply. A vigorous analytical approach is presented to provide a universal design guideline. The analysis unveils the sensitivity of the circuit characteristic to device parameters. The proposed circuit is fabricated in a 0.18μm CMOS technology and operates down to a supply voltage of 1.2 V. The circuit yields 20 ppm/°C of temperature coefficient in typical case and 50 ppm/°C of temperature coefficient in worst...
A new low voltage, high PSRR, CMOS bandgap voltage reference
, Article 2008 IEEE International SOC Conference, SOCC, Newport Beach, CA, 17 September 2008 through 20 September 2008 ; 2008 , Pages 345-348 ; 9781424425969 (ISBN) ; Atarodi, M ; Chahardori, M ; Sharif University of Technology
2008
Abstract
A new low voltage bandgap reference (BGR) in CMOS technology, with high power supply rejection ratio (PSRR) is presented. The proposed circuit uses a regulated current mode structure and some feedback loops to reach a low voltage, low power and high PSRR voltage reference. The circuit was designed and simulated in 0.18um CMOS technology, with a power supply of 1.4 volt. The results show PSRR is 65dB at 1MHz and the output voltage variation versus temperature (-40 to 140) is less than 0.1%. This circuit shows robustness against process variation. ©2008 IEEE
A low power 1.2 GS/s 4-bit flash ADC in 0.18 μm CMOS
, Article Proceedings of IEEE East-West Design and Test Symposium, EWDTS 2013 ; 2013 ; 9781479920969 (ISBN) ; Sharifkhani, M ; Sadughi, S ; Sharif University of Technology
2013
Abstract
A low power 4-bit flash ADC is proposed. A new power reduction technique is employed which deactivates the unused blocks in the converter structure in order to reduce the power consumption. A new method for built-in threshold voltage generation together with a new offset calibration method is used to further reduce the power consumption in the converter. Monte-Carlo simulation shows that after calibration both the INL and the DNL are lower than 0.35 LSB. The converter achieves 3.5 effective number of bits (ENOB) at 1.2 GS/s sampling rate after the offset calibration is performed. It consumes 10 mW from a 1.8 V supply, yielding a FoM of 560 fJ/conversion.step in a 0.18 μm standard CMOS...
A 4-Bit, 1.6 GS/s low power flash ADC, based on offset calibration and segmentation
, Article IEEE Transactions on Circuits and Systems I: Regular Papers ; Volume 60, Issue 9 , 2013 , Pages 2285-2297 ; 15498328 (ISSN) ; Sharifkhani, M ; Sadughi, S ; Sharif University of Technology
2013
Abstract
A low power 4-bit, 1.6 GS/s flash ADC is presented. A new power reduction technique which masks the unused blocks in a semi-pipeline chain of latches and encoders is introduced. The proposed circuit determines the unused blocks based on a pre-sensing of the signal. Moreover, a reference voltage generator with very low static power dissipation is used. Novel techniques to reduce the sensitivity to dynamic noise are proposed to suppress the noise effects on the reference generator. The proposed circuit reduces the power consumption by 20 percent compared to the conventional structure when a Nyquist rate OFDM signal is applied. The INL and DNL of the converter are smaller than 0.3 LSB after...
Investigating different circuit styles for digital circuits using organic transistors
, Article 2007 International Symposium on Integrated Circuits, ISIC, Singapore, 26 September 2007 through 28 September 2007 ; 2007 , Pages 5-8 ; 1424407974 (ISBN); 9781424407972 (ISBN) ; Ayatollahi, A ; Fakhraie, S. M ; Chahardori, M ; Sharif University of Technology
2007
Abstract
In search of low cost and flexible substrates organic transistors have been suggested as an alternate to silicon transistors. Level 1 model extraction, investigating different circuit styles and proposing two new circuit styles for organic integrated circuits is done in this paper. First, level 1 model of organic transistor is found using ID-VDS characteristics of transistors reported by [9]. After that different design styles used in CMOS digital integrated circuits are reviewed and the functionality of these styles for organic integrated circuits is investigated. Two new circuit styles have been proposed in this section which have better performance for organic circuits comparing with...
A compact mixer and DAC for implementation of a direct conversion OQPSK transmitter
, Article 2007 IEEE Region 10 Conference, TENCON 2007, Taipei, 30 October 2007 through 2 November 2007 ; 2007 ; 1424412722 (ISBN); 9781424412723 (ISBN) ; Mehrmanesh, S ; Zamanlooy, B ; Atarodi, M ; Sharif University of Technology
2007
Abstract
A compact low power circuit for implementation of a direct conversion OQPSK modulator is proposed. The circuit consists of a digital to analog converter, a low pass filter and an up-converter mixer. By embedding these three blocks, the circuit performance is enhanced and the total power consumption is reduced. The mixer is designed base on a Gilbert cell with on chip inductor loads. Instead of transconductance transistors of Gilbert cell, a fully deferential current mode DAC is used and proficiently a low pass filter is embedded between them and therefore the linearity of total system is improved. All of circuits are designed based on 0.18 μm CMOS technology with a single 1.8 volt power...
Systematic Design of Low Power Flash ADC
, Ph.D. Dissertation Sharif University of Technology ; Sadughi, Sirus (Supervisor) ; Sharifkhani, Mohamad (Co-Advisor) ; Atarodi, Mojtaba (Co-Advisor)
Abstract
Considering the drastical increasing of greenhouse gases in the atmosphere, especially carbon dioxide, reduction of these gases seems necessary to combat global warming. Fossil fuel power plants are one of the main sources of CO2 emission. In this thesis, CO2 capture from a natural gas fired combined cycle power plant using different oxygen percent in air feed is studied. Aspen Plus was used to evaluate the effect of this capture technology on the plant efficiency and energetic parameters of the system. Aspen Hysys is used to simulate Amine absorption tower and Air Separation cryogenic tower. Since the oxygen production plant, CO2 capture and transport are cost and energy intensive, the cost...
Probability of missed detection as a criterion for receiver placement in MIMO PCL
, Article IEEE National Radar Conference - Proceedings, 7 May 2012 through 11 May 2012, Atlanta, GA ; 2012 , Pages 0924-0927 ; 10975659 (ISSN) ; 9781467306584 (ISBN) ; Chitgarha, M. M ; Radmard, M ; Nayebi, M. M ; Sharif University of Technology
IEEE
2012
Abstract
Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar
An efficient method for the ring opening of epoxides with aromatic amines by Sb(III) chloride under microwave irradiation
, Article Journal of Chemical Research ; Issue 4 , 2008 , Pages 220-221 ; 03082342 (ISSN) ; Hashemi, M. M ; Mottaghi, M. M ; Foroughi, M. M ; Sharif University of Technology
2008
Abstract
SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity
Resource allocation for uav-enabled integrated sensing and communication (isac) via multi-objective optimization
, Article ICASSP, IEEE International Conference on Acoustics, Speech and Signal Processing - Proceedings ; Volume 2023-June , 2023 ; 15206149 (ISSN); 978-172816327-7 (ISBN) ; Naghsh, M. M ; Karbasi, M ; Nayebi, M. M ; Sharif University of Technology
Institute of Electrical and Electronics Engineers Inc
2023
Abstract
In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit...
MIMO radar signal design to improve the MIMO ambiguity function via maximizing its peak
, Article Signal Processing ; Volume 118 , 2016 , Pages 139-152 ; 01651684 (ISSN) ; Radmard, M ; Nazari Majd, M ; Karbasi, S. M ; Nayebi, M. M ; Sharif University of Technology
Elsevier
2016
Abstract
One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function...
Detection-localization tradeoff in MIMO radars
, Article Radioengineering ; Volume 26, Issue 2 , 2017 , Pages 581-587 ; 12102512 (ISSN) ; Radmard, M ; Chitgarha, M. M ; Bastani, M. H ; Nayebi, M. M ; Sharif University of Technology
2017
Abstract
Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance...
Antenna placement and power allocation optimization in MIMO detection
, Article IEEE Transactions on Aerospace and Electronic Systems ; Vol. 50, Issue 2 , April , 2014 , pp. 1468-1478 ; Chitgarha, M. M ; Majd, M. N ; Nayebi, M. M ; Sharif University of Technology
2014
Abstract
It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive...
Ambiguity function of MIMO radar with widely separated antennas
, Article Proceedings International Radar Symposium ; 16 -18 June , 2014 ; ISSN: 21555753 ; Chitgarha, M. M ; Nazari Majd, M ; Nayebi, M. M ; Sharif University of Technology
2014
Abstract
There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas
Choosing the position of the receiver in a MISO passive radar system
, Article European Microwave Week 2012: "Space for Microwaves", EuMW 2012, Conference Proceedings - 9th European Radar Conference, EuRAD 2012 ; 2012 , Pages 318-321 ; 9782874870293 (ISBN) ; Majd, M. N ; Radmard, M ; Nayebi, M. M ; Sharif University of Technology
2012
Abstract
By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only...
Adaptive filtering techniques in passive radar
, Article Proceedings International Radar Symposium, Dresden ; Volume 2 , June , 2013 , Pages 1067-1078 ; 21555753 (ISSN) ; 9783954042234 (ISBN) ; Radmard, M ; Majd, M. N ; Nayebi, M. M ; Sharif University of Technology
2013
Abstract
One of the most important obstacles in passive radar applications is removing the direct signal from the target channel. Otherwise, week echoes from the targets in the target channel would be ignored due to the limited dynamic range of the system. One of the most effective techniques in this field is using adaptive filters. In this paper various adaptive filters are introduced and their performances are shown and compared
Ambiguity function based receiver placement in multi-site radar
, Article 2016 CIE International Conference on Radar, RADAR 2016, 10 October 2016 through 13 October 2016 ; 2017 ; 9781509048281 (ISBN) ; Chitgarha, M. M ; Nazari Majd, M ; Nayebi, M. M ; Sharif University of Technology
2017
Abstract
It has been shown that using multiple antennas in a radar system improves the performance considerably, since multiple target echoes are received from different aspect angles of the target. In this way, the target detection is improved. However, when using multiple antennas, some problems, such as designing the transmit signals, synchronization, etc. emerge that should be solved. One of such problems is the receiver placement. Receiver placement deals with choosing a proper position for the receive antenna in order to optimize the whole system's performance. In this paper, a receiver placement procedure based on improving the radar ambiguity function is proposed for the case of a multisite...
Improving MIMO radar's performance through receivers' positioning
, Article IET Signal Processing ; Volume 11, Issue 5 , 2017 , Pages 622-630 ; 17519675 (ISSN) ; Radmard, M ; Nazari Majd, M ; Nayebi, M. M ; Sharif University of Technology
Institution of Engineering and Technology
2017
Abstract
By employing the MIMO (multiple-input-multiple-output) technology in radar, some new problems emerged, that, in order to benefit the MIMO gains in radar, it was necessary to solve them suitably. One of such obstacles is determining the positions of receive antennas in a MIMO radar system with widely separated antennas (WS MIMO radar), since it is shown that the antennas' positions affect the whole system's performance considerably. In this study, a proper receivers' positioning procedure is proposed. To do this end, four criteria are developed based on the proposed MIMO detector and the MIMO ambiguity function. The simulations verify that the proposed positioning procedure improves the...
Silylation of hydroxy groups with HMDS under microwave irradiation and solvent-free conditions
, Article Phosphorus, Sulfur and Silicon and Related Elements ; Volume 177, Issue 2 , 2002 , Pages 289-292 ; 10426507 (ISSN) ; Saidi, M. R ; Bolourtchian, M ; Heravi, M. M ; Sharif University of Technology
2002
Abstract
Phenols and alcohols are silylated with hexamethyldisilazane (HMDS) under microwave irradiation in solvent-free condition in good to excellent yields
An intelligent solvent selection approach in carbon capturing process: a comparative study of machine learning multi-class classification models
, Article Results in Engineering ; Volume 23 , 2024 ; 25901230 (ISSN) ; Hosseinpour, M ; Salimi, M ; Boroushaki, M ; Amidpour, M ; Sharif University of Technology
2024
Abstract
Carbon capture is crucial for mitigating climate change and achieving global emissions reduction targets. Among various technologies, absorption-based methods using aqueous solvents are among the most common and efficient, offering high capture rates and retrofit capabilities for existing industrial facilities. However, selecting the optimal solvent is challenging due to its direct impact on the performance, efficiency, and cost-effectiveness of the carbon capture process. This research introduces a novel multi-class classification methodology for solvent selection in carbon capture. Leveraging a dataset of 656 data points, including features such as temperature, pressure, molar ratio, and...