Sharif Digital Repository

Erasure codes are widely used in data storage systems to protect against disk failures. Employing erasure codes in an array of Solid-State Drives (SSDs) in storage systems necessitates designers to revisit different characteristics in comparison to Hard Disk Drives (HDDs), due to non-mechanical property of SSDs. One of the most important characteristics of SSDs is their limitation on the number of Program/Erase (P/E) cycles. By taking into account the characteristics of SSDs, this paper presents a comprehensive analysis to investigate the effects of three well-known erasure codes on the endurance and performance of SSD-based disk subsystems. The three erasure codes, i.e., Reed-Solomon,... 

Erasure codes are applied in both HDD and SSD storage systems to improve the reliability. The design of erasure codes for SSD-based systems should be performed with respect to a specific feature of SSDs, i.e., endurance. Endurance is defined as the number of Program/Erase (P/E)-cycles that one SSD can endure for reliable operation. The common metric for comparing the endurance of two systems is the number of P/E-cycles, which is yielded by time-consuming simulations. This paper proposes two new metrics called DPD-factor and GDP-pattern, for comparing the effect of erasure codes on the endurance of systems based on their encoding designs, without simulation. With respect to the endurance,... 

International Data Company (IDC) has estimated the total amount of digital data stored in the world will reach 40 thousand Exabytes at the end of 2020. The idea of accessing this volume of data, anywhere at any time by exploiting commodity hardware, led to the introduction of cloud storage. The abounded rate and variety of failures in the equipment used in cloud storage systems, placed fault tolerance, at top of the challenges in these systems. Hadoop Distributed File System (HDFS) has provided cloud with reliable storage via replication. Storage overhead of replication is high and therefore it's going to be replaced with erasure codes. Despite the significant number of researches on... 

We propose a nonlinear method for the analysis of the time series for the spatial position of a bead trapped in optical tweezers, which enables us to reconstruct its dynamical equation of motion. The main advantage of the method is that all the functions and parameters of the dynamics are determined directly (non-parametrically) from the measured series. It also allows us to determine, for the first time to our knowledge, the spatial-dependence of the diffusion coefficient of a bead in an optical trap, and to demonstrate that it is not in general constant. This is in contrast with the main assumption of the popularly-used power spectrum calibration method. The proposed method is validated... 

A Gaussian laser beam tightly focused through a high-numerical-aperture objective lens, so-called optical tweezers, is widely used for piconewton-range force spectroscopy. Utilizing a proper value for parameters such as bead size, numerical aperture of the objective, and power of the laser is always a challenge. Here, we show which set of values for the parameters can maximize lateral trapping efficiency. Our results show that for a high-numerical-aperture force spectroscopy, a bead with a diameter of 4–5 µm is suitable, and that for manipulation using large beads, utilizing a proper value for laser power and numerical aperture of the objective is crucial. We present a practical method for... 

The use of Solid State Drives (SSDs) has been increased in storage systems due to high performance and low power consumption. However, some inherent properties of SSDs result in different behavior for SSDs in comparison with Hard Disk Drives (HDDs). As an inherent property, the Bit Error Rate (BER) of SSDs increases, when the number of Program/Erase (P/E) cycles arises. This increment leads to two effects in an array of SSDs during its operation: (1) different BER on different SSDs of the system (SSD-variant BER), and (2) different BER in different time moments (time-variant BER). With respect to these two effects, the reliability evaluation of SSD-based RAIDs would be different from... 

Optical tweezers have proved to be indispensable tools for micro-manipulation. However, the application of large forces using optical tweezers requires high laser intensity, which could be destructive in the case of biological samples. By embedding magnetite nanoparticles in a polystyrene matrix, we get a trap stiffness ∼15 times higher than that of similar plain beads as a result of the response to both the electric and magnetic fields of the laser beam. Our approach allows for measurement of the magnetic properties of materials in the range of the laser frequency. Our theoretical calculations predict that incorporating the effective complex permeability and permittivity for a microbead... 

The wear-out of flash-based Solid-State Drives (SSDs) is a main concern that significantly affects their reliability. One major parameter that accelerates SSD wear-out is the number of write-cycles committed to flash chips. The number of write-cycles in SSD-based disk subsystem is highly dependent on the erasure code implemented in Redundant Array of Independent Disks (RAIDs). In this paper, we investigate the impact of erasure codes and the configuration of storage subsystems (i.e., the number of disks participated in the RAID array and stripe unit size) on the endurance of storage systems. The number of write-cycles is considered as a metric to evaluate the endurance of storage system. We... 

Abstract: A metal-free method for activation of hydrogen peroxide (H2O2) is introduced using piperidinium trifluoroacetate (PPHTFA) ionic liquid as catalyst. The catalyst has been used for selective oxidation of thioanisole to its corresponding sulfoxide at room temperature. It was found that the selectivities were reduced by increasing the reaction temperature. In this work, no organic solvents or metallic salts were used for activation of H2O2. Mechanistic studies suggested that the reaction proceeds via in situ formation of trifluoro hydroperoxy species as an active catalytic intermediate. Formation of the catalytic intermediate was screened by NMR, IR and Mass Spectroscopy analysis.... 

A Gaussian laser beam tightly focused through a high-numerical-aperture objective lens, so-called optical tweezers, is widely used for piconewton-range force spectroscopy. Utilizing a proper value for parameters such as bead size, numerical aperture of the objective, and power of the laser is always a challenge. Here, we show which set of values for the parameters can maximize lateral trapping efficiency. Our results show that for a high-numerical-aperture force spectroscopy, a bead with a diameter of 4–5 µm is suitable, and that for manipulation using large beads, utilizing a proper value for laser power and numerical aperture of the objective is crucial. We present a practical method for... 

Optical tweezers are indispensable force spectroscopes. The trap stiffness and the linear force range of the instrument determine the working force range of the instrument. Here we show both theoretically and experimentallythat utilizing a circular obstruction at the back focal plane of the objective can significantly increase the maximumlinear force. For instance, utilizing a disk with an obstruction ratio of 0.773 could increase the maximum linearforce by a factor of ∼39 when a 3.4 μm polystyrene bead is trapped. We also show that this simple beam shapingmethod can significantly improve the maximum applicable force per unit power of the laser entering the objectivelens. © 2018 Optical... 

Optical tweezers are proven and indispensable micro-manipulation tools. It is very common to use an immersion-assisted high NA objective for optical trapping of micrometer-sized beads. However, such objectives suffer from low working depth range. Here we show, both by theory and experiment, that a dry objective can be utilized for optimal trapping of even sub-micrometer objects. For the first time, to the best of our knowledge, we were able to stably trap polystyrene beads with radii of 270 and 175 nm in 3D using an objective with numerical aperture of 0.9. © 2022 Optica Publishing Group  

The effect of contact geometry on fretting fatigue life was investigated by experiments and numerical simulation. The experiments were conducted for flat and cylindrical pads under the same contact normal force. The post-test examinations including crack growth measurements and fractography were carried out using optical and scanning electron microscopy (SEM). Numerical simulations of pad-specimen assembly with and without crack were performed using a finite element (FE) analysis. The experimental study revealed that the rate of crack growth was higher at the early stages of fretting fatigue for cylindrical pads. This stage corresponds to a higher KII for cylindrical contact model. After... 

The onset of fretting fatigue is characterized by material microstructural changes in which the extent of the damage is comparable to grain size, and hence, the microstructure characteristics could have a significant effect on fatigue crack initiation. In this paper, a three-dimensional finite element crystal plasticity framework is presented for simulation of the fretting fatigue. Controlled Poisson Voronoi tessellation (CPVT) method is employed to generate the polycrystalline region. In the CPVT method, regularity parameter controls the shape of grains. In this study, the impact of grain size and regularity parameter on crack initiation life and initiation site has been investigated.... 

The onset of fretting fatigue is characterized by material microstructural changes in which the extent of the damage is comparable to grain size, and hence, the microstructure characteristics could have a significant effect on fatigue crack initiation. In this paper, a three-dimensional finite element crystal plasticity framework is presented for simulation of the fretting fatigue. Controlled Poisson Voronoi tessellation (CPVT) method is employed to generate the polycrystalline region. In the CPVT method, regularity parameter controls the shape of grains. In this study, the impact of grain size and regularity parameter on crack initiation life and initiation site has been investigated.... 

Recent research studies on ductile fracture of metals have shown that the ductile fracture initiation is significantly affected by the stress state. In this study, the effects of the stress invariants as well as the effect of the reverse loading on ductile fracture are considered. To estimate the reduction of load carrying capacity and ductile fracture initiation, a scalar damage expression is proposed. This scalar damage is a function of the accumulated plastic strain, the first stress invariant and the Lode angle. To incorporate the effect of the reverse loading, the accumulated plastic strain is divided into the tension and compression components and each component has a different weight... 

Recent experiments on metals have shown that all of the stress invariants should be involved in the constitutive description of the material in plasticity. In this paper, a plasticity model for metals is defined for isotropic materials, which is a function of the first stress invariant in addition to the second and the third invariants of the deviatoric stress tensor. For this purpose, the Drucker-Prager yield criterion is extended by addition of a new term containing the second and the third deviatoric stress invariants. Furthermore for estimating the cyclic behavior, new terms are incorporated into the Chaboche's hardening evolution equation. These modifications are applied by adding new...