Sharif Digital Repository

Ultrafine-grained Al-CNT (2 and 4 vol%) composites were successfully fabricated using the flake powder metallurgy and hot pressing route, and the microstructure and tribological properties of the produced composites were studied. The results showed that the coefficient of friction and the wear rate of Al decrease with the addition of the CNT reinforcement. A carbon-rich film formed on the worn surfaces during wear test, which prevented the Al oxidation and yielded the self-lubricating effect for the composites. This improvement in the wear behavior of the composites can be attributed to the simultaneous effects of the ultrafine-grained matrix and strengthening and self-lubricating properties... 

In this paper, ultra-small CuO nanoparticles (NPs) were synthesized through a mechanochemical method using two different Cu-containing precursors (i.e. CuSO4·5H2O and CuCl2·2H2O), and their structure and antibacterial activity were studied. From the microstructural studies, it was observed that CuO NPs have a spherical morphology and a narrow size distribution with 7 and 14 nm median particle sizes for CuCl2·2H2O and CuSO4.5H2O precursors, respectively. The CuCl2·2H2O derived nanoparticles showed more antibacterial activity than CuSO4.5H2O derived nanoparticles. The minimum inhibitory concentration (MIC) of the synthesized nanoparticles (derived from both precursors) against E. coli and... 

Cu-CNT composites were fabricated by a flake powder metallurgy method, and their microhardness, electrical conductivity, frictional and wear properties were investigated. Homogenous distribution of CNTs in fine-grained Cu matrix was obtained using this process. Microhardness increased with the addition of CNT vol% up to 8% to the Cu matrix, while the conductivity decreased to 79.2 IACS %. Results showed that CNTs play a major role in improving wear resistance by forming a CNT-rich film that acts as a solid lubricant layer. In the synthesized composites, Cu- 4 vol% CNT composite exhibited the best wear and friction properties. The dominant wear mechanisms for the Cu-CNT composites were... 

Hybrid Cu-SiC composites have been highly considered in order to achieve a combination of electrical and thermal properties along with high strength and wear resistance. However, limited investigations have ever been conducted over the effects of using hybrid (combination of nano and micro size) particles on the wear resistance behavior of these composites. Hence, in the present study, Cu-SiC nanocomposite with 4 vol% nanosize and 4 vol% microsize SiC, and Cu-SiC microcomposite with 8 vol% micro- SiC were fabricated through mechanical milling and hot pressing process. Results revealed the homogeneous dispersion of SiC particles in the matrix, high densification, and ultrafine-grain matrix... 

In this study, SiC/Ti–Cu nanocomposite was fabricated by mechanical alloying and sintering process. Effects of SiC nano-reinforcement on phase transformation, microstructure and tribological and antibacterial properties Ti–Cu intermetallic alloy were studied. The microstructure of the powders and sintered materials was investigated using X-ray diffraction, and scanning/transmission electron microscopy. The results exhibited the formation of major TiCu and TiCu 4 , and minor Ti 2 Cu and Ti 2 Cu 3 nanocrystalline phases in the sintered Ti–Cu and SiC/Ti–Cu samples. With the addition of the nanoparticles, the amount of TiCu 4 phase increased. Reinforcing Ti–Cu intermetallic alloy by SiC... 

Hybrid Cu-SiC composites have been highly considered in order to achieve a combination of electrical and thermal properties along with high strength and wear resistance. However, limited investigations have ever been conducted over the effects of using hybrid (combination of nano and micro size) particles on the wear resistance behavior of these composites. Hence, in the present study, Cu-SiC nanocomposite with 4 vol% nanosize and 4 vol% microsize SiC, and Cu-SiC microcomposite with 8 vol% micro- SiC were fabricated through mechanical milling and hot pressing process. Results revealed the homogeneous dispersion of SiC particles in the matrix, high densification, and ultrafine-grain matrix... 

The demands for high-performance biomaterials are driving the development of new metallic alloys with improved mechanical and biological responses. In this study, a nanocrystalline Ti-Cu intermetallic alloy was prepared by a powder metallurgy route, and its application as an orthopedic material was evaluated by the microstructural, mechanical, corrosion, antibacterial, cytotoxicity and osseointegration examinations. Microstructural characterization revealed the formation of TiCu and Ti2Cu3 as major phases with 23 nm grain size in the structure of the alloy. The synthesized alloy exhibited ultra-high hardness of 10 GPa, acceptable toughness of 8.14 MPam1/2, a ∼98 % anti-bacterial rate against... 

Effects of SiC nanoparticles addition on synthesis and antibacterial properties of TiCu nanocrystalline powder prepared through high energy mechanical milling were studied. The results showed that the synthesis of TiCu powder in the presence of the nanoparticles was accelerated and after mechanical alloying for 20 h, a TiCu/SiC nanocrystalline powder with the crystallite size <5 nm, and 3.3% lattice micro-strain obtained. Further milling resulted in fully amorphous TiCu intermetallic alloy with more uniform distribution of SiC nanoparticles. The antibacterial activity of the synthesized powders was investigated by disk diffusion test. The TiCu/SiC nanocomposites showed enhanced antibacterial... 

Using flake powder metallurgy (FPM) technique, combined with high pressure torsion, super high strength-ductile Cu-CNT nanocomposite with high electrical conductivity is developed. The nanocomposite with 4 vol% CNT showed high tensile strength of ~474 MPa, high electrical conductivity of ~82.5% IACS as well as appreciable ductility of ~11%. According to microstructural studies, the excellent properties of the nanocomposite are attributed to the formation of trimodal grains, high density of twin and low angle grain boundaries, improvement in CNT and Cu interfacial bonding, and appropriate distribution and maintaining the microstructure of the nanotubes in the production process. The results... 

We introduce a 'high probability' framework for repeated games with incomplete information. In our non-equilibrium setting, players aim to guarantee a certain payoff with high probability, rather than in expected value. We provide a high probability counterpart of the classical result of Mertens and Zamir for the zero-sum repeated games. Any payoff that can be guaranteed with high probability can be guaranteed in expectation, but the reverse is not true. Hence, unlike the average payoff case where the payoff guaranteed by each player is the negative of the payoff by the other player, the two guaranteed payoffs would differ in the high probability framework. One motivation for this framework... 

In the present study, hardness and tribological properties of nanostructured copper reinforced with SiC nanoparticles of various volume fractions (0, 2, 4, and 6 vol%) were investigated. The nanocomposites were fabricated by high-energy mechanical milling and hot pressing method. The Cu-SiC nanocomposites showed enhanced hardness and wear resistance against WC counterface. The hardness and wear resistance of the nanocomposite increased with increasing the amount of SiC nanoparticles up to 2 vol% in the matrix, but they decreased at higher percentages of SiC (4 and 6 vol%). Flake formation-spalling and abrasion were identified as the predominant wear mechanisms. It was found that reducing the... 

In this paper, the rapid synthesis of nanostructured NiTi–Ni3Ti intermetallic alloy from titanium and nickel powders through mechanical alloying followed by microwave-assisted sintering process was investigated. The sintered samples at different temperatures exhibited major phases of NiTi– B2 and Ni3Ti, and minor phases of NiTi–B19′ and Ti2Ni. The density, porosity and microhardness of the sample varied based on the sintering temperature, in which the highest density and microhardness (~750 H V) were obtained at sintering temperature of 1100 °C. Based on the results of this research, the microwave-assisted sintering can be applied to fabricate Ni–Ti alloys with improved mechanical properties... 

In this paper, the rapid synthesis of nanostructured NiTi–Ni3Ti intermetallic alloy from titanium and nickel powders through mechanical alloying followed by microwave-assisted sintering process was investigated. The sintered samples at different temperatures exhibited major phases of NiTi– B2 and Ni3Ti, and minor phases of NiTi–B19′ and Ti2Ni. The density, porosity and microhardness of the sample varied based on the sintering temperature, in which the highest density and microhardness (~750 H V) were obtained at sintering temperature of 1100 °C. Based on the results of this research, the microwave-assisted sintering can be applied to fabricate Ni–Ti alloys with improved mechanical properties... 

A 0.15% C-1.2% Si-1.7% Mn steel was intercritically annealed at 780 °C for 5 min and then isothermally held at 400 °C for 4 min followed by oil quenching to room temperature and the annealed microstructure consist of 75% ferrite, 15% bainite and 10% retained austenite was produced. Samples of this steel with triple phase structure were tensile tested at temperature range of 25-450 °C. Stress-strain curves showed serration flow at temperature range of 120-400 °C and smooth flow at the other temperatures. All of the stress-strain curves showed discontinuous yielding at all testing temperatures. Both yield and ultimate tensile strength decreased with increasing temperature, but there exists a... 

Titanium alloys are widely used in various areas, particularly in medical and dental industries, due to their remarkable properties. Still, the optimum cutting conditions for titanium alloys are under consideration. Ti alloyed with Cu has been reported to provide unique properties such as good mechanical performance, good biocompatibility, acceptable corrosion resistance, and relatively lower melting point. The properties of Ti-Cu alloys mentioned above are sensitive to microstructure. They are highly dependent on microstructural characteristics such as the formation, growth, and morphological features of intermetallics and precipitates, dependent on the amount of Cu and the manufacturing... 

In this study, the microstructural and mechanical features of monolithic pure Cu and Cu matrix nanocomposites reinforced with three different fractions (2, 4, and 6 vol%) of SiC nanoparticles (n-SiC) fabricated via a combination of high energy mechanical milling and hot pressing techniques were investigated. The fabricated composites exhibited homogeneous distribution of the n-SiC with few porosities. It was found that the grain refinement, the planar features within the grains, and the lattice strains increase with increase in the n-SiC content. The yield and compressive strengths of the nanocomposites were significantly improved with increases in the n-SiC content up to 4 vol%; then they... 

In this research, carbon nanotube decorated with Cu nanoparticles (CNT/Cu) was synthesized by a new solvothermal process. Solvothermal treatment of CuSO4 and NaOH was completed in ethanol containing ultrasonically dispersed CNTs at 160 °C for 3 h. In the solvothermal process, Cu nanoparticles were heterogeneously deposited on the surface of COOH-functionalized CNTs through the reduction of the Cu+2 ions. Cu nanoparticles with the size of ≈8 nm on CNTs (and some in the solution) and strong bonding between Cu and CNT were obtained by the used process. Microstructural characterization revealed that the solvothermal method is an appropriate method for producing homogenous CNT/Cu nanostructure.... 

Cu/SiC nanocomposite powders with homogeneously distributed nanosize SiC particles were produced by high energy mechanical milling (MM). Scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and micro-hardness and density measurements were performed to understand the effects of microstructure and hardness on compaction behavior during MM. The effects of SiC nanoparticle content and mechanical milling time on apparent density (AD) and tap density (TD) of the nanocomposite powders were systematically investigated. The Hausner ratio (HR), defined as TD to AD, were estimated to evaluate friction between the particles. Increasing MM duration and SiC content resulted... 

In this study, an attempt has been made to fabricate Cu-SiC nanocomposites by flake powder metallurgy and high-pressure torsion processing techniques at room temperature. Pure Cu and a mixture of Cu and nano-sized SiC powders were mechanically milled separately for 3 h and then green compacts were prepared by uniaxial pressing under 1 GPa pressure. The green compacts experienced 6-turn high-pressure torsion under a pressure of 6 GPa to prepare bulk Cu and Cu-SiC samples. The microstructures of the consolidated samples were characterized using an X-ray diffractometer and a high resolution scanning/transmission electron microscope, and the mechanical properties were evaluated by microhardness,... 

High bainite dual phase steel has been subjected to tension test at different temperatures from 25 to 500 °C with strain rate of 4.6 × 10-4 s-1 to investigate the effect of temperature on its mechanical properties. Stress-strain curves of steels showed serration flow at temperature range of 200-350 °C and smooth flow at the other temperatures. In agreement with previous studies on some steels, peaks in the variations of yield strength (YS) and ultimate tensile strength (UTS) and minima in ductility were observed at temperature range of 200-350 °C which are various manifestations of dynamic strain aging (DSA). It has been also found that ferrite volume fraction has no effect on the...