Sharif Digital Repository

This paper presents a novel method for fabrication of bone-like Ti6Al4V foamy core@compact shell composite for utilization as substitutive implant for cortical bone having porous core. Seven prototypes with core-diameters of 0, 6, 8, 10, 12, 14 and 16 mm surrounded by dense shells of respective thicknesses 8, 5, 4, 3, 2, 1 and 0 were produced by an innovative two-stage packing/compaction sintering method. Density, porosity, Young's modulus and compression strength of the prototypes depended on the core diameter. Mechanical strength and Young's modulus of 10@16 (10 mm core, 16 mm diameter prototypes) resembled that of the human ulna bone. Creation of foam at the center was achieved by... 

A numerical modeling procedure was used to quantify calibration chamber size and boundary effects for cone penetration testing in sand. In the numerical analyses, chamber diameter and boundary conditions were varied to investigate the effects of chamber size and boundary conditions on cone tip resistance. These analyses show that, for loose sand, a chamber-to-cone diameter ratio of 33 is sufficient for the boundaries to have no influence on the cone tip measurements. However, for very dense sand, the numerical analyses show that the chamber-to-cone diameter ratio should be more than 100 to ensure that boundaries have no influence on cone tip measurements. Numerical analysis indicates that,... 

A numerical analysis is presented to model the cone penetration test (CPT) tip resistance in layered soil. Analyses are performed for two-layer soils composed of either sands with different relative densities or different materials (sand and clay). Parametric numerical modeling is used to determine the distance that a cone senses a new upcoming soil layer interface or a layer interface behind. Analyses are also carried out for a thin sand layer embedded in soft clay. It is seen that the full tip resistance may not be reached in thin stiff layers. This is especially true for penetration in thin dense sand layers interbedded in softer clay. A correction factor is suggested to correct the cone... 

An array of metallic posts sandwiched between two parallel metal plates supports highly-confined surface waves that can be regarded as spoof surface plasmons. This structure which is called the parallel-plate ladder waveguide (PPLWG) can be used for implementing THz guided-wave devices. In this paper, the effect of post shapes on waveguiding characteristics of PPLWG is analyzed and realization of certain devices such as couplers using the proposed structure is investigated  

Mechanical milling proceeded by sintering was used to synthesize nanostructured temperature-resistant TZM alloy. Milling under Ar for different times (1, 2, 3, 5, 10, 15, 20, 25, and 30 h) and sintering at 1500, 1600 and 1700 °C for 30, 45, 60 and 90 min resulted in increasing of low-energy grain boundaries (LEGBs) and dispersion of TiC and ZrC with a size of ~ 65 nm in the matrix near LEGBs. Morphology and grain size of the products were determined from scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns, almost precisely. Optimum density of nanostructured TZM alloy ~ 9.95 ± 0.01 g/cm 3 was achieved by sintering at 1700 °C for 90 min  

A two-stage hydrogen-reduction/sintering procedure was used to synthesize W-15 wt%Cu nano-composite tablets. Hydrogen-reduction was carried out at 600, 650, 700 and 750 °C for 15-90 min and sintering was performed at 1100, 1150, 1200 and 1250 °C for 60 min. Morphology and grain size of the products were rigorously investigated by scanning electron microscope (SEM), X-ray diffractometer (XRD) and nano-particle Zeta-sizer. Maximum consolidation of the nano-composite product was achieved at 1200 °C. Hydrogen-reduction at 700 °C for 90 min showed an average particle size of ∼72.9 nm. Total reduction was achieved at higher temperatures and longer times. The mixture had a homogeneous structure... 

The main challenges of biological implants are suitable strength, adhesion, biocompatibility and corrosion resistance. This paper discusses fabrication, characterization and electrochemical investigation of anodized Ti6Al4V without and with a hydroxyapatite (HA) layer, HA/TiO2 nanoparticles (NPs) and HA/TiO2 nanotubes (HA/anodized). X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS) were used to characterize and compare properties of different samples. Dense HA with uniform distribution and 12.8 ± 2 MPa adhesive strength enhanced to 19.2 ± 4 MPa by the addition of TiO2 nanoparticles and enhanced to 23.1 ± 4 MPa by the... 

Owing to the expensive and time-consuming nature of durability experiments, finite element based durability analysis is quite prevalent in the automotive industry. Numerical fatigue life analyses are typically divided into two different categories, the quasi-static methods which are faster and the dynamic methods which are more accurate. The aim of this paper is to compare the inertia relief and modal dynamic approaches in terms of formulation, accuracy and computation time. The chosen case study is the fatigue life of the vehicle body which is considered the main load-bearing component in a vehicle. By utilizing multi-body dynamics model and driving the vehicle on different standardized... 

Outpatient appointment scheduling problems have recently gained increasing attention. This paper provides a comprehensive review of recent analytical and numerical optimization studies that present decision-support tools for designing and planning outpatient appointment systems (OASs). A structure for organizing the recent literature according to various criteria is provided, including a framework that classifies decisions at the strategic, tactical, and operational levels. The OAS literature is evaluated from four perspectives: problem settings, environmental factors, modeling approaches, and solution methods. In addition, research gaps and areas of opportunity for future research are... 

In this paper, the elastic solution to the problem of an isotropic bi-material full-space reinforced by a perfectly bonded thin film across the media interface and subjected to arbitrary asymmetric interfacial loading is addressed. To not include any simplifications, the thin film is first considered as a layer having a finite thickness, and with the aid of Fourier expansion of Muki's potential functions in Hankel transformed space, the formulation of the problem is obtained for a tri-material full-space. Then, knowing that the flexural stiffness of the thin film is negligible, its thickness and shear modulus are assumed to tend to zero and infinity, respectively, such that its in-plane... 

Fast, accurate and efficient sensing is of important aspects in cognitive radio technology. A new sensing circuit is proposed using a phase frequency detector for cognitive radio applications. Using this method, spectral sensing can be done in a very short time by a low cost, low power circuit, compared with available implemented methods. The PFD circuit resolves different frequencies without the need of variable filter bandwidth or the banks of filters. Also it accelerates sensing procedure because of short time needed to detect the signal. Simulations show the accurate operation of this method and comparison with other methods shows faster sweep rates  

In this paper, a mechanism for fabrication of nanostructured hydroxyapatite coating on TiO2 nanotubes is presented. Also, the physical, biological, and nanomechanical properties of the anodized Ti6Al4V alloy consisting TiO2 nanotubes, electrodeposited hydroxyapatite, and the hydroxyapatite/TiO2 nanotubes double layer coating on Ti6Al4V alloy implants are compared. Mean cell viability of the samples being 84.63 % for uncoated plate, 91.53 % for electrodeposited hydroxyapatite, and 94.98 % for hydroxyapatite/TiO2 nanotubes coated sample were in the acceptable range. Merely anodized prototype had the highest biocompatibility of 110 % with respect to the control sample. Bonding strength of... 

Fast, accurate and efficient sensing is of important aspects in cognitive radio technology. We propose a simple, practical design for two-dimensional sensing in spectral and spatial domain. In fact detection and localization of signal are done in a wide band elliptical array. Two sets of phase differences help to fast calculation of frequency and angle of arrival. We study the constraints, advantages and accuracy of the method. ©2009 IEEE  

Impure rhenium and molybdenum bearing solution was passed through a column of Varian strong base anionic resin for selective adsorption of rhenium and molybdenum ions from the solution. Elution of molybdenum and rhenium was carried out using 2 N NaOH and 0.2 N NH4SCN, respectively. The effect of resin bed height on breakthrough time was investigated. Experimental and theoretical curves were compared with good agreement. The results showed that the behavior pattern of these curves was repeatable and almost constant. © 2006 Elsevier B.V. All rights reserved  

Realistic description of fractured reservoirs demands primarily for a comprehensive understanding of fracture networks and their geometry including various individual fracture parameters as well as network connectivities. Newly developed multiple-point geostatistical simulation methods like SIMPAT and FILTERSIM are able to model connectivity and complexity of fracture networks more effectively than traditional variogrambased methods. This approach is therefore adopted to be used in this paper. Among the multiple-point statistics algorithms, FILTERSIM has the priority of less computational effort than does SIMPAT by applying filters and modern dimensionality reduction techniques to the... 

Gold nanorods (GNRs) can be used in various biomedical applications; however, very little is known about their in vivo tissue distribution by radiolabeling. Here, we have developed a rapid and simple method with high yield and without disturbing their optical properties for radiolabeling of gold rods with iodine-131 in order to track in vivo tissue uptake of GNRs after systemic administration by biodistribution analysis and γ-imaging. Following intravenous injection into rat, PEGylated GNRs have much longer blood circulation times. We have developed a rapid and simple method for radiolabeling of gold rods with iodine-131 in order to track in vivo tissue uptake of gold nanorods after systemic... 

This paper studies the effective parameters of a skilled service in playing tennis and determines their relationship with skill deals. Effective service in tennis plays an important role in gaining more desirable result and the most important factor of success in getting scores depends on the player's skills in serving an effective service. The characteristics of a good service are the high speed of the ball and the precision of landing the ball. The several parameters affecting on these two characteristic in the service, are studied in this paper. Therefore, the Kinematic parameters of 8 Iranian professional tennis athletes of first division tennis league and also 8 non-professional Iranian... 

ZnS nanoparticles were synthesized through a one-step precipitation process. Effect of time and temperature on the formation reaction was investigated. The synthesized samples were characterized by X-ray diffraction (XRD), ultraviolet (UV) visible absorption and photoluminescence (PL) spectrophotometry. Based on XRD and UV-Vis data, the particles produced at 70 °C had a mean particle size of about 5 nm. Increasing time and temperature of the synthesis reaction resulted in photoluminescence intensification. PL spectroscopy helped understanding the adsorption kinetics of oxygen on ZnS nanoparticles during the precipitation synthesis process. Fabrication of ZnS structures with appropriate... 

The objective of economic dispatch (ED) problem is minimizing the operating cost and finding the point where the total output of the generations equals the total power that must be delivered. In that point the incremental cost of power generation is also equal for all generators. Considering the presence of uncertainty and inaccuracy in the data, fuzzy set theory is an appropriate method to solve the economic dispatch problems. In this paper, a modified fuzzy economic dispatch is formulated to solve the problem under the competitive electricity market uncertainties. Also, available spinning reserve is optimally allocated to market participants. The formulated optimization problem it then... 

The rupturing process of a membrane, located between two fluids at the center of a three-dimensional channel, is numerically investigated. The smoothed particle hydrodynamics (SPH) and the finite element method (FEM) are used, respectively, for modeling the fluid and solid phases. A range of pressure differences and membrane thicknesses are studied and two different rupturing processes are identified. These processes differ in the time scale of the rupture, the location of the rupture initiation, the level of destruction and the driving mechanism. © 2019 by the authors